Sanyo ECR-238 - Page 12

9. PROGRAMMING
DATE AND TIME SETTING
Key Sequence
<P mode>
(A) 0000000--[@/FOR/TIME]--(B) QOOCOO)-@/FOR/TIME}
A=Date format (0~2) |B=Time format (0~2)
A=0: MM DD YY B=0: *24-hours system
A=1: DD MM YY B=1: A.M of 12-hours system
A=2: YY MM DD B=2: P.M of 12-hours system
(1) To pint the date in the order of month, day and year.
Enter zero (0), and then enter a six-digit number (MMDDYY)
ex . April 30, 1999 ... 043099
(2) To pint the date in the order of day, month and year:
Enter
one
(1),
and
then
enter
a
six-digit
number
(DDMMYY)
ex. 30 April, 1999 ... 1300499
(3) To pint the date in the order of day, month and year:
Enter two (2), and then enter a six-digit number (YYMMDD)
ex. 1999, April, 30 ... 2990430
(4) *24-hour mode means that the hour after noon go from
"13" to "24",
ex) 9:30 A.M 24 hour mode ...
12 hour mode ...
9:30 P.M 24 hour mode ...
12 hour mode ...
0093000
1093000
0213000
2093000
RECEIPT NUMBER SETTING
A maximum four digit number can be programmed as the
starting receipt number. Each time you take a Z-report, the next
receipt starts from the number programmed here, or it continues
per programming. (SYSTEM PROGRAMMING. , item D)
Key Sequence
<P mode>
(3)--ST ALL--0000)--[#/NS]--[#/NS]
xox : Initial Receipt Number (0000~9999)
ex. : Receipt number=500
3 [ST ALL] 500 [#/NS] [#/NS]
REPORT ID CODE AND MACHINE NUMBER
A two-digit ID code and a two-digit machine number can be
programmed.
!D
code
is
used
to
take
periodic
terminal
reports
and GT (Grand Total) for security purpose.
Key Sequence
<P mode>
(4)--ST ALL--(ABCD)--[#/NS]--[#/NS]
AB : ID code (00~99)
CD : Machine number (00~99)
PERCENT RATE SETTING FOR % KEY
A
preset
percent
rate
can
be
programmed
to
percent
keys
(%1,
%2).
A
percent
key
[%1]
can
be
positive
for
mark-up
or
negative
for
discount
operation
depending
on
programming.
Key
Sequence
<P
mode>
(XXXXX)--[%1, %2]
XXXXX = Percent rate x 1000
ex) 10.5% for[%1] —> 10500 [%1]
MACHINE SIZE SETTING
Key Sequence
<P mode>
(10)--ST ALL--(A B C D)--[#/NS]--[#/NS]
+8= Five Rappen mode
+4= Norway rounding
+2= GST rounding
+1= Gross GST mode
Five Rappen rounding mode
Norway rounding mode
GST rounding in Canada
GST rounding in Canada
+8= Australia rounding
+4= GST in Singapore
Australia rounding mode
GST in Singapore mode
Use the terminal as 10-department
Selection of maximum Department number
> Incase of 10-department , the following selection is
required. B=+1, C=0
Decimal position for Print & Display
0: DP=0
1: DP=1
2: DP=2
3: DP=3
PRINT LINE ELIMINATION
Key Sequence
<P mode>
(1)--ST ALL--(A B C D E F)--[#/NS]--[#/NS]
+1= Joumal mode,
+0= Receipt mode
Department section on General report +4= non Zero skip,
Joumal mode/Receipt mode
+0= zero skip
PLU report +2= non zero skip,
+0= zero skip
GT (Grand Total) line on Daily Z report +1= non print,
+0= print
Department Refund on report +4= non pnint,
+0= print
Transaction Void on report +2= non print,
+0= print
Void on report +1= non print,
+0= print
% +4= non print,
+0= print
rate line on receipt/joumal
PLU line on receipt/joumal +2= non print,
+0= print
Subtotal line on receipt/joumal +1= non print,
+0= print
+2= non print,
+0= print
+1= non print,
+0= print
+4= non print,
+0= print
Time on receipt/joumal
Date on receipt in R & M mode
F= +4] Tax total line on receipt/joumal
0~3 | Number of delayed receipt issuing
~10-