1. Safety Precautions in Servicing Work
Please
read
the "Safety Precautions" section carefully to prevent any accidents during service repair
and
provide a safe product .
• Loss
or
damage which
may
result from failing to heed these precautions and degree
of
their urgency, the precaution
have
been
classified ioto the
three
categories
&Danger
This
indication
shows
the
content
of
the
result
in
the
death
or
serious
injure
of
the
operator
or
other
persons.
&Warning
This iodicates a potentially hazardous sitoation arisiog from the mishandliog
or
mis-operation
of
the unit which,
if
not
avoided, could result
io
the death orserious iojury
of
the operator
or
other
persons.
&Caution
This iodicates a potentially hazardous sitoation arisiog from the mishandliog
or
mis-operation
of
the unit which,
if
not
avoided,
may
result
io
mioor iojury
of
the operator
or
other persons
and property damage .
• The figure sign classifies the contents that must
be heeded,
and
is explaioed. (The followiog sign is an example.)
6.
1bis symbol calls
attention
to
a
danger,
warning
or
caution,
so please
take
care.
0
This symbol calls attention to
an
action which the operator is prohibited from performiog,
so
take
care
.
•
This symbol calls attention to an action which
must
be
performed
or
which the operator is
iostructed to perform, so
tske
care.
&
Warning
Always
unplug
thc;unit
when
carrying
out
inspection
or
repairs.
• Do
not
damage
or
change
the
power
cord
.
This
may
lead
C
• Always
unplug
the
unit
from.
the
outlet
when
assembling,
6)
to electric shocks
or
fire.Placing heavy objects on
the
disassembling.
inspecting,
or
replacing
parts.Failure
to
power
cord,
heating.
or
pulling
it
could
result
in
damage.
PI_pull
0lIl:
a
observe
the
above
could
lead
to electric
shock.
or
injury.
Pl""='
fUIlPly
phi'
Always
return
the
wiring
to
its
original
condition
after
carrying
• Do not splice
the
power
cord,
plug
it
into
an
extension
out
inspection
or
repairs
on
the
unit.
cord.
or
use
it
with
multiple
plugs
in a single
outlet.
&
•
Tighten
the
lead
holden so
that
the
lead
wires
do
not
6)
Failure
to
observe
the
above
could
result:in
electric
touch
revolving
parts,
high-temperature
parts,
shocks,
heating
'"
fue.
high-pressure
parts,
or
edges (sides)
of
parts.
Contact
could
lead
to
ma1fimctions,
electric
shock,
or
tire.
~
Take sufficient care
of
electric shocks.
0
• Always
replace
damaged
or
worn
power
cord
or
lead
•
Take
sufficient
care
of
electric
shocks
from
the
charged
wires.Failure
to
observe
the
above
could
result
in
electric
c.utiowl
of
1111
parts
'"
lead temllnals.
shock,
beating
or
tire.
electric:
shock
Always use specified
parts
when repairing.
0
•
Parts
marked
with
it
are
safety
parts.
These
parts
are
0
•
Confirm
that
there
is
no
dust
and
that
the
plug
is
secure,
inserting
it
all
the
way
in.
Dust
or
bad
connection
could
important
in
maintaining
safety.
While
replacing,
always
result
in
electric shock
or
tire.
use
the
specified
parts.
0
•
When
repajring,
always
use
the
part
listed
on
service
parts
table
for
the
appropriate
model
and
appropriate
tools.
Also,
under
no
circumstances
are
modifications
to
the
unit
to
be
carried
out.
Failun:
to
observe
the
above
could
result
in
electric
shock,
heating
or
fire.
&
Caution
Beware
of
burns
due
to high
_perature.
&
•
Measure
the
insulation
resistance
after
repe:irs
and
@
con:fum
that
is at least
5M
(1
.
•
Take
care,
as
after
operation
the
chamber
door,
chamber,
A
problem
in
the
insulation
can
lead
to
electronic
and
piping sections
are
extremely
hot.
shock.
_,_
Always
wear
gloves
when
repejring
or
inspecting.
&
• Confirm
that
the
position
of
attached
parts,
condition
&
of
the
wiring,
and
soldering,
or
crimp
connections
are
• Use gloves
to
avoid
injury
from.
the
edge
ofmeta11ic
normal.An
abnormality
can
lead
to
heating,
:fire
or
surface.
electric
shock.
-1-
To Next Page
Loading...
Need help?
General
