Need help?Do you have a question about the Satel ACU-220 and is the answer not in the manual?
Explains the function and capabilities of the ACU-220 controller in alarm systems.
Lists key capabilities like two-way communication, encryption, and device support.
Identifies components labeled on the ACU-220 circuit board diagram.
Details the purpose and function of each terminal on the ACU-220.
Explains the purpose of DIP-switches for mode, antenna, and address configuration.
Configures the controller's operational mode using DIP switches 9 and 10.
Chooses the transmitting antenna (AN1 or AN2) via DIP switch 8.
Sets the controller's address for INTEGRA/INTEGRA Plus panels using DIP switches 1-5.
Details the 4 OC type outputs (TPR, CON, JAM, LBA) for system problem reporting.
Explains the 4 inputs (AR1-AR4) used to control wireless device operation.
Explains the 8 OC type outputs (OUT1-OUT8) for indicating device status or control.
Guidelines for selecting an optimal installation site considering radio range and environment.
Instructions for cable routing, enclosure mounting, and hole preparation.
Details on connecting the controller to INTEGRA/VERSA panels via communication buses.
Overview of the ABAX 2 Soft program and its main menu interface elements.
Describes additional menu options and the "Connection" window for establishing communication.
Step-by-step procedures for connecting the ABAX 2 Soft program to the ACU-220 controller.
Explains settings within the ABAX 2 Soft program's configuration interface, including controller info and parameters.
Details on the "Devices" tab for managing wireless devices, their types, inputs, and outputs.
Viewing controller status, inputs, jamming information, and communication history.
Explains the graphs feature for monitoring radio signal levels and potential interference.
Details on the "Comm. history" tab for analyzing device communication logs.
Describes the "Keyfobs" tab for managing keyfobs and their assignments.
Explains the "Keyfob state" tab for viewing keyfob battery, signal, and firmware status.
Lists the main categories of ABAX 2 wireless devices: detectors, sirens, keypads, keyfobs.
Lists various types of wireless detectors supported by the ABAX 2 system.
Lists supported wireless sirens and 230V AC controllers, plus other devices like repeaters.
Describes the INT-KWRL2 and VERSA-KWRL2 keypads and their function.
Lists the main categories of ABAX 2 wireless devices: detectors, sirens, keypads, keyfobs.
Process for registering wireless devices to the ACU-220 controller, including serial number entry.
Explains data storage and automatic assignment for devices connected to INTEGRA/INTEGRA Plus panels.
Explains data storage and automatic assignment for devices connected to VERSA panels.
Step-by-step guide for adding wireless devices using DLOADX for INTEGRA/INTEGRA Plus panels.
Instructions for removing wireless devices using the DLOADX program.
Instructions for removing wireless devices using the LCD keypad.
Step-by-step guide for adding wireless devices using DLOADX for VERSA/VERSA Plus/VERSA IP panels.
Instructions for removing wireless devices using the DLOADX program for VERSA systems.
Steps to add wireless devices using the ABAX 2 Soft program for the universal module.
Steps to remove wireless devices using the ABAX 2 Soft program for the universal module.
Parameters for configuring the controller's behavior, including tamper response and communication period.
Further controller settings, including jamming detection and firmware update options.
Describes test mode and synchronize function for system diagnostics and service.
Introduces ARU and Always active settings for wireless devices.
Detailed configuration settings for specific devices using the DLOADX program.
Detailed configuration settings for more devices using the DLOADX program.
Detailed configuration settings for APD-100, APD-100 Pet, and APMD-150 devices via DLOADX.
Detailed configuration settings for ARD-100, ASD-150/250, ATD-100, AVD-100 devices via DLOADX.
Instructions for configuring devices using the LCD keypad for INTEGRA/INTEGRA Plus systems.
Instructions for configuring devices using the LCD keypad for VERSA systems.
Explains how detectors operate based on input states (passive/active mode) and system arming.
Explains how sirens (ASP-200, ASP-215) operate and are triggered by outputs.
Explains how expander zones/outputs are assigned and their sensitivity settings.
Explains how wireless controllers (ASW-100/210) operate and activate relays.
Explains how radio signal repeaters are activated by mains loss or battery trouble.
Detailed configuration settings for ADD-200, AGD-200, and AMD-202 devices.
Detailed configuration settings for AOCD-260, AOD-210, and APD-200 devices.
Detailed configuration settings for APD-200 Pet, APMD-250, ARD-200, ASD-250, ATD-200 devices.
Explains how detectors operate based on input states (passive/active mode) and system arming.
Explains how sirens (ASP-200, ASP-215) operate and are triggered by outputs.
Explains how keyfob data is stored and assigned to users in INTEGRA/INTEGRA Plus systems.
Managing keyfobs using the DLOADX program connected to VERSA panels.
Procedures for adding keyfobs, assigning buttons to functions, and LEDs.
Assigning system zones to keyfob LEDs for status indication.
Steps to remove keyfobs from the system configuration.
How keyfobs control controller outputs and provide status information for the universal module.
Steps for updating the ACU-220 controller's firmware using the update program.
Steps to reset the controller to its original factory default configuration.
Key electrical parameters like supply voltage, current consumption, and operating temperature.
Details on security grade, standards compliance, and physical dimensions of the device.
General| Power Supply | 12 V DC |
|---|---|
| Radio frequency band | 868 MHz |
| Operating Temperature | -10 °C to +55 °C |
| Communication Interface | RS-485 |
| Current Consumption | Max. 150 mA |
| Supported Protocols | Satel ACU Protocol |
To Next Page
