The Savant WIS-SWS102 (snow white) and WIS-LAS102 (light almond) wireless switches are designed to function within the Savant
Control system to switch most lighting loads. This includes incandescents, magnetic and electronic low voltage, CFL, and LED.
The Savant Metropolitan wireless switches replace any standard 120V AC light switch or dimmer. With the addition of the Savant WI3-
xxx102 Auxiliary Control, these switches are compatible with most 3-way wiring designs for multi-location control.
Finally, the WIS-xxx102 communicates with most 802.11 b/g/n wireless networks which allow it to be added to the Savant Control
system for complete control of all lighting requirements over the local wireless network.
Box Contents
•
Metropolitan Switch without faceplate
•
(2) Mounting Screws 6/32 x ¾ inch
•
(5) Wire Nuts
•
Quick Reference Guide (this document)
Optional Accessories
•
1 to 4-gang faceplates
•
Black conversion kits
Specifications
32° to 104° F (0° to 40° C)
10% to 90% Relative Humidity (non-condensing)
4.13 in (10.49 cm) / Shipping 7.0 in (17.78 cm)
2.38 in (6.05 cm) / Shipping 4.5 in (11.43 cm)
1.81 in (4.60 cm) / Shipping 3.0 in (7.62 cm)
Recommended Back Box Depth Dimensions
Recommended Back Box Depth Dimensions
All Metro switches require a standard U.S. electrical back box
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep
All Metro switches require a standard U.S. electrical back box
• Recommended - 3.5 in (8.89 cm) deep
• Minimum - 2.25 in (5.72 cm) deep
Incandescent, Magnetic/Electronic Low Voltage, CFL, LED
WPA™, WPA2™, WPA1™ + WPA2™, WEP
FCC Part 15 | UL
For more details, refer to the Regulatory section
Minimum Supported Release
Minimum Supported Release
Front View
Ambient Light Sensor - Senses the level of ambient light in the room and adjusts the LED brightness on the front
panel. The ambient light sensor operation can be modified using RacePoint Blueprint®.
Reset Button - The reset button has two functions:
• Press and release the reset button. After button is released, all LEDs on the front panel illuminate for two-
seconds and then flash twice. Pressing the reset button causes the switch to calibrate itself to the circuit it is
being installed to. After the switch calibrates itself, it then reboots. After the reboot, the LED sequencing that
is now displayed on the main button is determined by whether the device had previously been connected to a
network. Refer to LED Sequencing table.
Note: The reset button should always be pressed after the Metropolitan device is installed.
• Press and hold the reset button for five seconds until all LEDs on the front panel illuminate. The LEDs remain
on for two seconds and then flash twice. The switch then reboots and reverts to Provisioning Mode. In
Provisioning Mode, the LEDs on the main button flash in an alternating pattern waiting for the switch to be
provisioned. Refer to LED Sequencing table.
Switch LED - LED lights when button is pressed. LEDs are also used to indicate the state of the switch when
connecting to a network. Refer to LED Sequencing table. Once configured in Blueprint, the switch LED shows
the scene state.
Service Switch - The service switch removes power from the load (red wire). Toggle the service switch to Off
whenever changing the load. The service switch can also be used to power cycle the switch.
Rear View
Device wires are all a five inch #16 AWG stranded wire.
Neutral - Return path for voltage.
Traveler - Wire to the Auxiliary Controller for multi-location control.
Line - Wire to hot wire from AC power source.
Metropolitan Wireless Switch | 009-1337-01 | 150522
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
Savant.com | 508.683.2500
Metropolitan Wireless Switch - WIS-xxx102
Quick Reference Guide
To Next Page
Need help?
General
