Scag Power Equipment SW32-14FS User Manual (English)

Questions and Answers:

C
cheryl99Jul 31, 2025
Why does my Scag Power Equipment SW32-14FS leave strips of uncut grass?
- S
  Susan MayJul 31, 2025
  If your Scag Power Equipment Lawn Mower leaves strips of uncut grass in the cutting path, it could be due to several reasons. The blades might be dull or worn, or they might be incorrectly sharpened, so sharpen or replace them. Low engine RPM can also cause this, so ensure you run the engine at full RPM. Other possible causes include a slipping belt (adjust belt tension), a plugged deck with grass accumulation (clean the underside of the deck), ground speed being too fast (slow down), wet grass (cut after it has dried), or bent blades (replace the blades).
C
curtisjonesAug 6, 2025
How to fix occasional uncut grass blades from Scag Power Equipment Lawn Mower?
- S
  Sheila EvansAug 6, 2025
  If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, it could be due to several factors. Ensure the engine is running at full RPM. Adjust your ground speed to suit the conditions, as moving too fast can cause this issue. Avoid cutting wet grass, and ensure your blades are sharp. A buildup of grass under the deck can also cause this, so clean the underside of the deck. Finally, check and adjust the belt tension if the belts are slipping.
K
Kelly PeckAug 12, 2025
What to do if Scag Power Equipment SW32-14FS has uneven cut on flat ground?
- J
  Jennifer DanielAug 12, 2025
  If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, scalloped, or rough appearance, there are several potential causes. A worn blade lift can cause this, so replace the blade. Ensure the blade is mounted correctly with the cutting edge toward the ground. Clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if the blade angle is too great. If the deck is improperly mounted or the spindle area is bent, consult your authorized SCAG dealer. Also, ensure that the blade is sharp.
R
Robert MirandaAug 18, 2025
Why does my Scag Power Equipment Lawn Mower leave a ridge?
- M
  Miranda LewisAug 18, 2025
  If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, check that the tire pressures are equal and the wheels are even; adjust if necessary. Also, examine the deck to ensure it is level side to side and correct it if it is not. If the deck is mounted incorrectly, it's best to consult your authorized SCAG dealer.
W
william20Aug 25, 2025
How to prevent strips of uncut grass between cutting paths with Scag Power Equipment SW32-14FS Lawn Mower?
- M
  Michael HamptonAug 25, 2025
  To prevent strips of uncut grass between cutting paths with your Scag Power Equipment Lawn Mower, increase the overlap of each pass.

Scag Power Equipment SW32-14FS Specifications

General

Brand	Scag Power Equipment
Model	SW32-14FS
Category	Lawn Mower
Language	English

Summary

General Information

Introduction

Overview of the mower's construction and importance of the operator's manual.

Direction Reference

Defines terms like 'Right', 'Left', 'Front', 'Rear' relative to the operator's position.

Servicing Engine and Drive Train Components

Outlines manual limitations for engine/transmission service, recommending dealer support.

Symbols

Lists common symbols used in the manual and their corresponding meanings.

Safety Information

Safety Introduction

Emphasizes the operator's critical role in safety and the need for thorough training.

Signal Words

Explains the meaning of DANGER, WARNING, and CAUTION signal words used in safety messages.

Before Operation Considerations

Lists essential precautions and checks to perform before starting mower operation.

Operation Considerations

Key safety practices and warnings to follow during normal mower operation.

Maintenance Considerations and Storage

Guidelines for maintaining the mower and proper procedures for storage.

Using a Spark Arrestor

Information regarding spark arrestor requirements in specific geographical areas.

Safety and Instructional Decals

Lists and describes important safety decals found on the mower.

Specifications

Engine Specifications

Details on engine type, displacement, cylinders, fuel, and starter systems.

Electrical Specifications

Information on the starter, interlock switches, and instrument panel components.

Engine Deck Specifications

Details on the drive system, steering, wheels, tire pressure, and fuel tank capacity.

Cutter Deck Specifications

Specifications for the cutter deck, including type, construction, and cutting width.

Weights and Dimensions

Provides crucial weight and dimension data for different mower models.

Productivity

Estimates acres cut per day based on cutting width and operating speed.

Operating Instructions

Controls and Instrument Identification

Identifies and explains the function of all mower and engine controls.

Safety Interlock System

Explains the function and importance of the mower's safety interlock system.

Initial Run-In Procedures

Details the necessary checks and procedures for the first 20 hours of operation.

Starting the Engine

Provides a step-by-step guide for safely starting the mower's engine.

Ground Travel and Steering

Guidance on learning to operate the mower's ground speed and steering controls.

Forward Travel Operation

Instructions for controlling forward movement, steering, and stopping the mower.

Reverse Travel Operation

Instructions for controlling reverse movement, steering, and stopping the mower.

Engaging the Deck Drive

Procedure for safely engaging the mower deck and cutter blades.

Hillside Operation

Safety precautions and techniques for operating the mower on slopes.

Parking the Mower

Steps for safely parking the mower on a level surface.

After Operation Procedures

Tasks to perform after completing mower operation, including cleaning.

Removing Clogged Material

Procedure for safely clearing clogged material from the discharge chute.

Moving Mower with Engine Stopped

Instructions for manually moving the mower when the engine is not running.

Mowing Recommendations

Tips for optimal cutting performance and achieving a good lawn appearance.

Troubleshooting Cutting Conditions

Troubleshooting: Stringers

Identifies causes and cures for uncut grass 'stringers' in the cut.

Troubleshooting: Streaking in Path

Identifies causes and cures for uncut grass streaks in the main cutting path.

Troubleshooting: Streaking Between Paths

Identifies causes and cures for uncut grass strips between mower passes.

Troubleshooting: Uneven Cut on Flat Ground

Identifies causes and cures for wavy or scalloped cuts on flat terrain.

Troubleshooting: Uneven Cut on Uneven Ground

Identifies causes and cures for uneven cuts on varied or uneven terrain.

Troubleshooting: Sloping Ridge

Identifies causes and cures for sloping ridges appearing across the cutting path.

Troubleshooting: Scalping

Identifies causes and cures for scalping or cutting too close to the ground.

Troubleshooting: Step Cut

Identifies causes and cures for a step cut ridge in the center of the cutting path.

Troubleshooting: Slope Cut Ridges

Identifies causes and cures for sloping ridges across the width of the cut.

Adjustments

Drive Control Adjustments

Details on adjusting steering control rods for proper brake engagement.

Cutter Deck Belt Adjustments

Instructions for adjusting cutter deck belt tension for optimal performance.

Belt Alignment

Importance of belt alignment and seeking dealer service for wear issues.

Adjusting Cutting Height

Details on adjusting deck height and pitch for desired cutting results.

Blade Height Adjustment

Procedure for adjusting blade height using spacers on the spindle shaft.

Custom-Cut Baffle Adjustment

Instructions for adjusting the baffle height for various grass types and conditions.

Electric Clutch Adjustment

Procedure for adjusting the electric clutch air gap for proper engagement and function.

Maintenance

Maintenance Service Intervals Chart

Chart detailing recommended maintenance tasks and their required intervals.

Lubrication Guide

Details on lubrication intervals, lubricants, and key fitting points.

Engine Oil Procedures

Instructions for checking and changing engine oil and the oil filter.

Engine Fuel System

Safety precautions and procedures for filling the mower's fuel tank.

Engine Air Cleaner

Procedure for cleaning or replacing the engine's air cleaner element.

Cutter Blades

Instructions for inspecting, sharpening, and replacing cutter blades.

Tire Maintenance

Guidance on the importance of regularly checking tire pressures.

Illustrated Parts List

Approved Attachments and Accessories

Lists Scag-approved attachments and accessories compatible with the mower.

Replacement Decals and Information Plates

Lists part numbers for various replacement decals and information plates.

Limited Warranty - Commercial Equipment

Related product manuals

Scag Power Equipment SW32-14BV

24 pages

Scag Power Equipment SW32-13BV

24 pages

Scag Power Equipment SW32-13KA

28 pages

Scag Power Equipment SW36-13KH

28 pages

Scag Power Equipment SW36-13KA

28 pages

Scag Power Equipment SWM-52

28 pages

Scag Power Equipment SWZT36-14FS

WALK-BEHIND SWZ-19KAI

92 pages

Scag Power Equipment SW32-14FS User Manual

Table of Contents

Questions and Answers:

Scag Power Equipment SW32-14FS Specifications

Summary

General Information

Introduction

Direction Reference

Servicing Engine and Drive Train Components

Symbols

Safety Information

Safety Introduction

Signal Words

Before Operation Considerations

Operation Considerations

Maintenance Considerations and Storage

Using a Spark Arrestor

Safety and Instructional Decals

Specifications

Engine Specifications

Electrical Specifications

Engine Deck Specifications

Cutter Deck Specifications

Weights and Dimensions

Productivity

Operating Instructions

Controls and Instrument Identification

Safety Interlock System

Initial Run-In Procedures

Starting the Engine

Ground Travel and Steering

Forward Travel Operation

Reverse Travel Operation

Engaging the Deck Drive

Hillside Operation

Parking the Mower

After Operation Procedures

Removing Clogged Material

Moving Mower with Engine Stopped

Mowing Recommendations

Troubleshooting Cutting Conditions

Troubleshooting: Stringers

Troubleshooting: Streaking in Path

Troubleshooting: Streaking Between Paths

Troubleshooting: Uneven Cut on Flat Ground

Troubleshooting: Uneven Cut on Uneven Ground

Troubleshooting: Sloping Ridge

Troubleshooting: Scalping

Troubleshooting: Step Cut

Troubleshooting: Slope Cut Ridges

Adjustments

Drive Control Adjustments

Cutter Deck Belt Adjustments

Belt Alignment

Adjusting Cutting Height

Blade Height Adjustment

Custom-Cut Baffle Adjustment

Electric Clutch Adjustment

Maintenance

Maintenance Service Intervals Chart

Lubrication Guide

Engine Oil Procedures

Engine Fuel System

Engine Air Cleaner

Cutter Blades

Tire Maintenance

Illustrated Parts List

Approved Attachments and Accessories

Replacement Decals and Information Plates

Limited Warranty - Commercial Equipment

Related product manuals