www.scheppach.com
GB
|
39
Ensure as little vibration as possible of the tool via
regular maintenance and stable parts on the device.
Replace worn parts immediately.
The specied vibration emission value has been meas-
ured according to a standardised test procedure and
can be used for comparison of one power tool with
another.
It has been reported that vibration from hand-held pow-
er tools can contribute to a condition called Raynauds
syndrome (white nger syndrome) in certain individ-
uals. Raynaud‘s syndrome is a vascular disease that
causes the small blood vessels on the ngers and toes
to cramp in spasms. The affected areas are no longer
supplied with sufcient blood and therefore appear ex-
tremely pale.
The frequent use of vibrating tools can cause nerve
damage in people whose circulation is impaired (e.g.
smokers, diabetics). If you notice unusual adverse
effects, stop working immediately and seek medical
advice. For long-term and regular users, it is therefore
recommended to closely monitor the condition of your
hands and ngers. Observe the following information
to reduce hazards:
1. Keep your body warm, especially your hands, es-
pecially in cool weather.
2. Take regular breaks and move your hands to pro-
mote circulation.
3. Limit the use of high vibration tools per day and
spread them over several days Make a work
schedule that limits vibration exposure.
4. Ensure as little vibration as possible of the tool via
regular maintenance and stable parts on the de-
vice. Replace worn parts immediately.
5. Change your working position regularly.
7. Unpacking
• Open the packaging and carefully remove the prod-
uct.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the rst time.
6. Technical data
Motor voltage 20 V DC
Engine output 0.4 W
Type of guide bar (pre-tted)
ROYAL 6”
CLQ4336
Type of saw chain (pre-tted)
ROYAL 6” DG06-
36-43P
Tank for chain lubricating oil
ca. 30 cm³ (30
ml)
Max. cutting speed 6.8 m/s
Max. cutting length 130 mm
Chain pitch 1/4”
Driving link thickness 0.043”/1.09 mm
Chain wheel tooth pitch
6 / 6.35 (1/4”)
Weight unfuelled, without cutting
gear approx.
1.1 kg
Weight unfuelled, with battery
approx.
1.7 kg
Technical changes reserved!
Noise and vibration
m Warning:Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A), please
wear suitable hearing protection.
Noise data
Sound power level L
WA
99 dB(A)
Sound pressure level L
pA
93 dB(A)
Uncertainty K
wa/pA
3 dB(A)
Vibration parameters
Vibration a
h
6 m/s
2
Uncertainty K
h
1.5 m/s
2
Information on the specied vibration emission
value
Warning:The actual vibration emission value present
during use of the machine may differ from the value
given in the instruction manual or by the manufacturer.
To be accurate, an estimate of the load level should be
made notoriously all work periods during actual use,
e.g. the times when the tool is off, idle and not in use. In
this way it is possible to signicantly reduce the degree
of stress throughout the entire working time.
When using this tool regularly, wear anti-vibration
gloves and avoid working in ambient temperatures of
10°C or less. Make a work schedule to spread the use
of high vibration tools over several days.
To Next Page
Loading...
General