EasyManua.ls Logo

Scheppach HP1200S - User Manual

Scheppach HP1200S
120 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Nachdrucke, auch auszugsweise, bedürfen der Genehmigung.
Technische Änderungen vorbehalten. Abbildungen beispielhaft!
Art.Nr.
5904610903
AusgabeNr.
5904610903_0301
Rev.Nr.
27/08/2021
HP1200S
DE
Rüttelplatte
Originalbedienungsanleitung
8
GB
Plate vibrator
Translation of original instruction manual
24
EE
Raputusplaat
Originaalkäitusjuhendi tõlge
37
LT
Vibracinė plokštė
Originalios naudojimo instrukcijos vertimas
50
LV
Tankintuvai
Oriģinālās lietošanas instrukcijas tulkojums
63
SE
Vibrationsplatta
Översättning av original-bruksanvisning
76
FI
Tärytyslevy
Käännös alkuperäisestä käyttöohjeesta
89
DK
Vibrationsplade
Oversættelse fra den oprindelige betjeningsvejledning
102

Table of Contents

Questions and Answers

  • D
    Daniel DominguezAug 18, 2025
    Why won't my Scheppach Construction Equipment engine start?
    • J
      Jenny WalkerAug 18, 2025
      Several factors can prevent your Scheppach Construction Equipment engine from starting. It could be due to a disconnected spark plug wire; make sure it's securely attached. Check if you're out of fuel or using stale fuel; if so, refill with fresh gasoline. Ensure the throttle control lever is in the starting position and the choke is properly set for a cold start. A blocked fuel line or a fouled spark plug can also be culprits, so clean the fuel line or clean/replace the spark plug. Lastly, if the engine is flooded, wait a few minutes before attempting to restart without priming.
  • C
    Cole TapiaAug 21, 2025
    Why is my Scheppach Construction Equipment engine running erratically?
    • C
      Carol HayesAug 21, 2025
      If your Scheppach Construction Equipment engine runs erratically, start by checking the spark plug wire to ensure it is connected and tightened. Make sure the unit is not running on CHOKE; if it is, move the choke lever to OFF. A blocked fuel line or stale fuel can also cause this issue, so clean the fuel line and refill the tank with fresh gasoline. Additionally, check for a plugged vent and clear it. Water or dirt in the fuel system can also lead to erratic engine performance, so drain the fuel tank and refill with fresh fuel. Finally, a dirty air cleaner can be the cause, so clean or replace it.
  • V
    Vanessa SteinAug 23, 2025
    Why is my Scheppach HP1200S engine overheating?
    • R
      Richard PhillipsAug 23, 2025
      Your Scheppach Construction Equipment engine may overheat due to a dirty air cleaner. Clean the air cleaner to resolve this. Restricted airflow can also cause overheating; remove the housing and clean it.
  • H
    hsanchezAug 26, 2025
    What to do if Scheppach HP1200S engine won't stop?
    • J
      James CooperAug 26, 2025
      If the engine on your Scheppach Construction Equipment won't stop when the throttle control is at the stop position, or if the engine speed doesn't increase properly when the throttle control is adjusted, it could be due to debris interfering with the throttle link. Clean any dirt and debris to resolve this issue. If the pull cord is damaged, contact a specialist dealer.
  • E
    Eric PrinceAug 28, 2025
    Why Scheppach Power Tool engine fails to start?
    • P
      pchambersAug 28, 2025
      If your Scheppach Power Tool engine won't start, several factors could be at play. First, ensure the spark plug wire is securely attached to the spark plug. Second, check your fuel: you might be out of fuel or using stale fuel, so fill up with clean, fresh gasoline. Third, make sure the throttle control lever is in the correct starting position, and for a cold start, position the throttle at choke. Additionally, a blocked fuel line or a fouled spark plug could be the culprit; in the first case, clean the fuel line, in the second - clean, adjust the gap, or replace the spark plug. Finally, if the engine is flooding, wait a few minutes before attempting to restart, and avoid priming it.
  • S
    sierra58Aug 31, 2025
    Why does my Scheppach Power Tool engine run erratically?
    • S
      Shannon MillerAug 31, 2025
      If your Scheppach Power Tool engine runs erratically, start by checking the spark plug wire to ensure it's connected and tightened. Make sure that the unit is not running on CHOKE, move choke lever to OFF. A blocked fuel line or stale fuel could also be the issue; clean the fuel line and refill the tank with clean, fresh gasoline. Also check for a plugged vent and clear it if necessary. Water or dirt in the fuel system can also cause problems, so drain the fuel tank and refill with fresh fuel. Finally, a dirty air cleaner can lead to erratic engine performance, so clean or replace the air cleaner.
  • S
    Stacey GraySep 2, 2025
    What to do if my Scheppach Power Tool engine overheats?
    • L
      Linda LewisSep 2, 2025
      If your Scheppach Power Tool engine overheats, the likely causes are a dirty air cleaner or restricted air flow. Clean the air cleaner to ensure it's not the cause. If the air flow is restricted, remove the housing and clean to allow for better ventilation.
  • T
    Timothy HendersonSep 4, 2025
    Why is my Scheppach Construction Equipment compactor difficult to control?
    • D
      dennisgregorySep 5, 2025
      If your Scheppach Construction Equipment compactor is difficult to control when pounding (machine jumps or lurches forward), it might be due to the engine speed being too high on hard ground. Try setting the throttle lever at a lower speed. If the shock absorber is too loose or damaged, contact a specialist dealer.
  • A
    Ann SilvaSep 7, 2025
    What to do if Scheppach Construction Equipment plate compactor has no compacting function?
    • S
      Shelby RiveraSep 7, 2025
      If your Scheppach Construction Equipment plate compactor has no compacting function or does not reach maximum speed, it could be due to damage on the exciter or plate, in which case you should contact a specialist dealer. Alternatively, the drive belt might be too loose and slipping on the pulley; try adjusting or replacing the drive belt.
  • C
    Courtney HortonSep 9, 2025
    Why is my Scheppach Construction Equipment losing oil?
    • S
      Sarah MartinSep 10, 2025
      If you notice oil loss from the engine or exciter of your Scheppach Construction Equipment, it could be due to a worn seal, in which case you should contact a specialist dealer. It could also be due to leaks on the housing.

Scheppach HP1200S Specifications

General IconGeneral
Voltage230 V
Max. splitting force12 tons
Max. splitting stroke520 mm
Frequency50 Hz
Max. splitting length520 mm
Hydraulic oil capacity4 L
Max. Pressure200 bar
Tank Capacity4 L

Related product manuals