www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
43
These parts include, among others, the cutting tool
and the retaining disk.
m Warning! Use only original manufacturer‘s re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450 7910700707
Spool TRICORD Ø450 7910702702
Spool TRICORD Ø2,8mmx4m 7910702704
Blade with 3 teeth Ø 255 x 1.4 7910700702
Transport guard for blade 3 teeth 3904801065
Blade with 4 teeth Ø 255 x 1.5 7910700705
Transport guard for blade 4 teeth 3904801066
Blade with 8 teeth Ø 255 x 1.5 7910700711
Transport guard for blade 8 teeth 3904801066
Safety shield for grass trimmer 3904803034
Pole pruner:
Saw chain Oregon 91PJ040X 7910700704
Guide rail Oregon 100SDEA318 3904801037
Saw chain 3/8.50-39 7910100732
Guide rail AL10-39-507P 7910100731
Transport guard for chain 3904801039
Extension for pole pruner 7910700710
Hedge trimmer:
Blade for hedge trimmer 400 mm 7910700703
Transport guard for blade 3904801043
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: spark plug, air lter, thread coil, blade,
saw chain, chain bar
* Not necessarily included in the scope of delivery!
Oiling the gears (pole saw)
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig. 47 (Q).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overll.
Check the hedge trimmer for obvious faults such
as:
• loose attachments
• worn or damaged components
• bent, broken or damaged cutting tools
• correctly attached and working covers and safety
devices
• wear, in particular, cutting tool play
Immediately replace damaged or blunt cutting
tools, even in the event of minor damage.
Oiling the gears, hedge trimmer
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig. 41 (P).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overll.
Oil the cutting tools and the angle adjustment with
environmentally friendly lubricant.
Adjusting the idle speed, Fig. 50
If the cutting device runs idle, correct the idle speed.
1. Allow the engine to warm for 3-5 minutes
(No high speeds!).
2. Turn the adjusting screw (S):
clockwise
- idle speed increases (+)
counterclockwise
- Idling speed decreases (-)
The idle speed is 3000 min
-1
Contact the manufacturer if the cutter continues
to run at idle. Do not continue to operate the unit!
The user is responsible for all damages caused
by non-compliance with instructions in this
manual. This also applies to non-authorized
modications of the tool, use of non-authorized
spare parts, accessories, working tools, unre-
lated and not intended use, secondary damages
due to use of faulty components.
Wear Parts
Even when used in the intended way, some compo-
nents are subject to normal wear. They have to be
replaced depending on the kind of duration of usage.
To Next Page
Loading...
Need help?
General
