Why Scheppach MFH5200-4P Lawn and Garden Equipment pole saw does not saw, it plucks or vibrates?
If your Scheppach Lawn and Garden Equipment pole saw doesn't saw and instead plucks or vibrates, check and reset the chain tension if it's too high. Have the chain sharpened or replace it if it's blunt. Re-attach the chain if it's attached incorrectly. Replace the chain if it's worn.
Why Scheppach Trimmer does not work at full power?
If your Scheppach Trimmer isn't working at full power, it might be overloaded, so avoid using force during mowing or trimming. The air filter could be contaminated, requiring cleaning or replacement. Also, the silencer might be blocked, so check the exhaust. For incorrect carburetor setup, contact the service center.
What to do if Scheppach Grass trimmer does not work at full power?
If your Scheppach Grass trimmer isn't working at full power, the cutting line might be too short or damaged, so feed more cutting line through or replace it. Also, the machine might be overloaded because the grass is too high, so cut the grass in phases.
Why Scheppach Brush cutter does not work at full power?
If your Scheppach Brush cutter isn't working at full power, the blades may be blunt or damaged, so sharpen or replace them. Alternatively, the cut material might be too high, causing machine overload, so cut the grass in phases.
Why does my Scheppach Trimmer start but stop?
If your Scheppach Trimmer starts but stops again, it might be due to an incorrect carburetor setting (idle speed). In this case, contact the service centre.
What to do if the cutting line cannot be fed through Scheppach MFH5200-4P?
If the cutting line cannot be fed through your Scheppach Lawn and Garden Equipment, the spool is likely empty, so replace it.
Why Scheppach Lawn and Garden Equipment grass trimmer does not work at full power?
If your Scheppach Lawn and Garden Equipment grass trimmer doesn't work at full power, the cutting line might be too short or damaged, so feed more cutting line through or replace it. If the machine is overloaded because the grass is too high, cut the grass in phases.
What to do if Scheppach MFH5200-4P saw chain becomes hot or lubrication doesn't work?
If the saw chain of your Scheppach Lawn and Garden Equipment becomes hot or the saw chain lubrication doesn't work, refill the oil if there is no oil in the tank. Clean the oil line if it is blocked. If the chain tension is too high, set the chain tension. Have the chain sharpened or replace it if it is blunt.
Why Scheppach MFH5200-4P machine does not work at full power?
If your Scheppach Lawn and Garden Equipment machine isn't working at full power, it might be overloaded, so avoid using force during mowing or trimming. A contaminated air filter can also cause this issue; clean or replace it. Make sure to check the exhaust because the silencer could be blocked. If the carburetor is set up incorrectly, contact the service centre.
Why Pole saw does not saw, it plucks or vibrates on Scheppach?
If your Scheppach Pole saw doesn't saw and instead plucks or vibrates, the chain tension might be too high, so check and reset it. The chain could be blunt, so have it sharpened or replace it. The chain might be attached incorrectly, so re-attach it. The chain may also be worn, so replace it.
Crucial safety precautions for operating the equipment, including personal protective equipment.
Covers safe working posture, fuel handling, avoiding hazards like vibration and exhaust fumes.
Step-by-step instructions for assembling handles, shafts, guards, and cutting heads.
Guides on how to safely start the engine and engage the cutting tools using choke and throttle.
Lists common equipment faults, their possible causes, and recommended remedies.
General| Maximum power | 1300 W |
|---|---|
| Angle adjustment | 165 ° |
| Engine displacement | 51.7 cm³ |
| Attachments quantity | 4 |
| Engine number of strokes | 2 |
| Hedge trimmer attachment | Yes |
| Hedge trimmer blade length | 24 mm |
| Brush cutter cutting diameter | 255 mm |
| Brush cutter number of blades | 1 |
To Next Page
