Why Scheppach MFH5200-4P machine does not work at full power?
If your Scheppach Lawn and Garden Equipment machine isn't working at full power, it might be overloaded, so avoid using force during mowing or trimming. A contaminated air filter can also cause this issue; clean or replace it. Make sure to check the exhaust because the silencer could be blocked. If the carburetor is set up incorrectly, contact the service centre.
How to fix a Scheppach Trimmer that does not start?
If your Scheppach Trimmer doesn't start, several factors could be at play. It might be due to a contaminated air filter (clean or replace it), a blocked fuel filter (clean or renew it), or simply a lack of fuel (re-fuel). There could be a fault in the fuel line, so check for kinks or damage. The engine might be stalled. In this case, remove, clean, and dry the spark plug, then pull the starter rope several times before re-fixing the spark plug. Also, ensure the spark plug cap is correctly attached and that the spark plug is clean. If none of these steps work, the starting device or carburetor may be faulty, or the engine may be damaged, requiring you to contact a service center or check the ignition cable.
Why Pole saw does not saw, it plucks or vibrates on Scheppach?
If your Scheppach Pole saw doesn't saw and instead plucks or vibrates, the chain tension might be too high, so check and reset it. The chain could be blunt, so have it sharpened or replace it. The chain might be attached incorrectly, so re-attach it. The chain may also be worn, so replace it.
Why saw chain becomes hot on Scheppach Pole saw?
If the saw chain on your Scheppach Pole saw becomes hot or the saw chain lubrication isn't working, there might be no oil in the tank, so refill it. The oil line could be blocked, so clean it. The chain tension might be too high, so set the chain tension. Alternatively, the chain could be blunt, so have it sharpened or replaced.
What causes the cutting tool to stop on a Scheppach Trimmer?
If the cutting tool stops while the engine of your Scheppach Trimmer is running, it might be blocked, so turn off the engine and remove the object. If there is an internal fault (drive shaft, gearbox) or a faulty clutch, contact the service centre.
What to do if Scheppach Trimmer works with interruptions?
If your Scheppach Trimmer is working with interruptions (sputtering), the spark plug may be sooty, so clean or replace it. If the carburetor is set up incorrectly or the on/off switch is faulty, contact the service centre.
Why is smoke generated by Scheppach Trimmer?
If smoke is being generated by your Scheppach Trimmer, it could be due to a wrong fuel mix. Use a two-stroke mixture at a ratio of 40:1. For incorrect carburetor setup, contact the service center.
Why does my Scheppach Trimmer start but stop?
If your Scheppach Trimmer starts but stops again, it might be due to an incorrect carburetor setting (idle speed). In this case, contact the service centre.
Why Scheppach Brush cutter does not work at full power?
If your Scheppach Brush cutter isn't working at full power, the blades may be blunt or damaged, so sharpen or replace them. Alternatively, the cut material might be too high, causing machine overload, so cut the grass in phases.
What to do if Scheppach Grass trimmer does not work at full power?
If your Scheppach Grass trimmer isn't working at full power, the cutting line might be too short or damaged, so feed more cutting line through or replace it. Also, the machine might be overloaded because the grass is too high, so cut the grass in phases.
Crucial safety precautions for operating the equipment, including personal protective equipment.
Covers safe working posture, fuel handling, avoiding hazards like vibration and exhaust fumes.
Step-by-step instructions for assembling handles, shafts, guards, and cutting heads.
Guides on how to safely start the engine and engage the cutting tools using choke and throttle.
Lists common equipment faults, their possible causes, and recommended remedies.
General| Maximum power | 1300 W |
|---|---|
| Angle adjustment | 165 ° |
| Engine displacement | 51.7 cm³ |
| Attachments quantity | 4 |
| Engine number of strokes | 2 |
| Hedge trimmer attachment | Yes |
| Hedge trimmer blade length | 24 mm |
| Brush cutter cutting diameter | 255 mm |
| Brush cutter number of blades | 1 |
To Next Page
