Scheppach Riwall PRO RPMT330

29GB
It is not allowed to operate the petrol cutting blade
in closed or poorly ventilated rooms.
• Rell the gasoline tank only outdoors, or in well-
ventilated areas.
• Gasoline and gasoline vapors are highly ammable.
Keep away from ammable materials and sources
of ignition, such as ovens or stoves.
• Do not smoke while refueling or operating the tool.
• Immediately wipe away spilled gasoline.
• Start the petrol cutting blade only at a location far
away from the place of refueling.
• Always make sure that the cover of the fuel tank is
well closed. Look out for possible leakage.
• When the engine is running or the engine is hot, it
is not allowed to open the cap of the fuel tank or
rell gasoline.
• Open the cap of the fuel tank slowly so that gasoline
vapor can escape.
• Make sure the handles are dry, clean, and free of
gasoline mixed with oil.
• Do not use the tool without exhaust pipe and when
the exhaust pipe guard is not properly installed.
• Do not touch the exhaust pipe, there is a risk of
burns.
• Only use the fuel recommended in the manual. Keep
gasoline only in containers designed for it, and store
it at a safe location.
• While cutting on a slope, always stand below the
cutting tool.
• Always make sure no objects or other debris is col-
lecting in the trimmer head, in the protective hood,
or in the engine.
• Always switch off the tool before you put it down.
• Do not use any wire, or anything similar in the line
spool.
• Only work during daylight, or when the area is il-
luminated well using lighting.
• Subject the tool to a visual inspection before each
use.
• Check, if all screws and connecting parts are tight-
ened.
• Always use both hands to hold the tool.
• Check the tool, and its components and guards for
damages, or wear and tear before each use, and
have it repaired, if necessary. Never make the de-
vices for protection and safety inoperable. Do not
use the tool, when damages or signs of wear be-
come apparent.
• Keep the tools clean and fully functional to ensure
better and safer work.
• Always maintain a safe distance between the tool
and your body during work.
• Always switch off the tool when work will be inter-
rupted or the location will be changed; wait until the
cutting tools have completely stopped, and turn off
the engine.
• Never leave the tool without supervision at the place
of work. Store the tool at a safe place when work
will be interrupted.
• Persons operating the machine must not be dis-
tracted, or one may lose control over the tool.
• Never use the tool during rain, in a humid or wet
environment, and do not store it outdoors.
• Should the tool become wet, wait until it is com-
pletely dry before you use it again.
• Before starting work, it is recommended to check the
objects to be cut for possible foreign objects and to
remove them. When despite of this you encounter
a foreign object during cutting, switch off the tool
and remove this object.
• If the tool is jammed by a foreign object (stones,
piles of grass), switch it off, and remove the object
using a blunt item. Never use your ngers to remove
jammed foreign objects, because this may cause se-
rious injuries.
• Always keep the running tool away from your body.
• Attention: the cutting tool still runs for some time
after the tool is switched off!
• Do not overload the engine, and do not use it for
work the tool is not designed for.
• Always make sure the ventilation openings are free
of dirt.
• Store the tool out of the reach of children.
• Store the tool at a safe and dry location.
• Check the engine for damages after impact, or other
damages.
• Keep body parts and pieces of clothing away from
the trimmer head when you start the engine, or keep
it running.
• Always keep in mind that especially during trim-
ming of lawn edges, gravel enclosures, and similar
locations stone and dirt can be hurled away from
the cutting line.
• Never cross roads or paths when the tool is switched
on.
• Never cut against hard objects such as stone, etc.
This way you avoid injuries, and damages to the tool.
• Never use the tool without the guards attached.
• Never use your hands to stop the cutting device.
• Always wait until it stops on its own.
• Hold and guide the trimmer head as close to the
ground as possible.
• Only cut grass growing on the ground. Do not cut
grass in cracks in walls, growing or on rocks, etc.
• Always make sure no objects, or other debris is col-
lecting in the trimmer head, in the protective hood,
or in the engine.
• Only use the tool, when the guard is attached.
• Always switch off the tool, before you put it down.
• Keep in mind that there is risk of injuries in the area
of the cutting device intended to cut off the line.
• CAUTION: The cutting tool continues rotating for a
few seconds after the engine is turned off.
• Put the tool down only after the cutting tool has
completely stopped and the motor is turned off.
• When the cutting tool is damaged, it must be re-
placed at once.
• Always use the original line only. Never use a metal
wire instead of the nylon line.
• Tool and cutting tools must be properly inspected
and serviced periodically. Damages must be re-
paired by a service center.