To Next PageTo Next PageHow to troubleshoot a Schumacher Electric Battery Charger that won't turn on?
If your Schumacher Electric Battery Charger doesn't turn on when properly connected, first check that the AC outlet is functional by testing it with another device or checking the fuse or circuit breaker. Also, inspect the power cord and any extension cords for loose connections.
What to do if Schumacher Electric Battery Charger will not turn on?
If your Schumacher Electric Battery Charger won't turn on even when properly connected, the issue might stem from the AC outlet or a poor electrical connection. Begin by checking the AC outlet for any tripped circuit breakers or blown fuses. Also, inspect the power cord and any extension cords for loose plugs.
Why Schumacher Electric Battery Charger is not charging when connected?
If your Schumacher Electric Battery Charger is connected and on, but the battery isn't charging, the problem likely lies in a poor connection. Make sure the clips are making good contact with the battery and the frame. Ensure the connecting points are clean and try rocking the clips back and forth to establish a better connection.
What to do if ammeter reading stays high on Schumacher Electric Battery Charger?
If your Schumacher Electric Battery Charger's ammeter reading stays high, it could mean that the battery is severely discharged or that the charger's voltage settings are incorrect. Try continuing to charge the battery for an additional two hours. If the problem persists, have the battery checked by a professional. Also, verify that the voltage settings on the charger are appropriate for your battery.
Why short or no start cycle when cranking engine with Schumacher Electric Battery Charger?
If you experience a short or no start cycle when cranking the engine with your Schumacher Electric Battery Charger, several factors could be responsible. You might be drawing more current than the Engine Start Rate allows. Be sure to wait 4 minutes between cranking attempts to allow both the battery and charger to cool down. Check for loose connections at the battery and frame, as well as at the power cord and any extension cords. Also, verify that the AC outlet has power by checking for tripped fuses or circuit breakers. The charger may have overheated, so ensure the vents are not blocked and allow it time to cool. If the battery is severely discharged, try charging it for 10-15 minutes at the highest manual rate to assist with cranking.
Why is my Schumacher Electric SE-125A Battery Charger making a clicking sound?
If your Schumacher Electric Battery Charger is making an audible clicking sound, it could be due to several reasons: the circuit breaker cycling, a defective battery, shorted battery cables or clips, a severely discharged battery, or reverse connections at the battery. Check the charger settings to ensure they are correct. Have the battery tested to rule out defects. Inspect the cables and clips for shorts, replacing them if necessary. If the battery is severely discharged, allow charging to continue, giving it time to recover; if it doesn't improve after 20 minutes, stop and have the battery checked. Finally, turn off the charger and correct any reversed lead connections.
What to do if Schumacher Electric Battery Charger has short or no start cycle when cranking engine?
If your Schumacher Electric Battery Charger experiences a short or no start cycle when cranking the engine, several factors could be at play. It might be due to drawing more current than the Engine Start rate allows, in which case, the crank time may be less than 3 seconds. Ensure you wait 3 minutes between cranks to cool the battery and charger. Check for poor connections at the battery and frame, and ensure the power cord and extension cord are securely plugged in. Also, verify that the AC outlet has power and that the charger vents are not blocked, as overheating can occur. If the battery is severely discharged, try charging it for 10-15 minutes at the 2 amp rate before attempting to crank again.
Why does my Schumacher Electric Battery Charger make a clicking sound?
A clicking sound from your Schumacher Electric Battery Charger can be caused by several factors. The circuit breaker might be cycling, indicating incorrect settings, so check the charger settings. The battery could be defective, or there might be shorted battery cables or clips. A severely discharged battery might also cause this, in which case, allow charging to continue. Finally, reverse connections at the battery can cause a clicking sound, so shut the charger off and correct the lead connections.
What to do if my Schumacher Electric SE-125A Battery Charger ammeter reading stays high?
If the ammeter reading on your Schumacher Electric Battery Charger remains high, it could mean that the battery is severely discharged; in that case, continue charging the battery for two more hours. It could also indicate the wrong battery voltage. If the problem continues, have the battery checked and verify the voltage settings on the charger are correct.
What to do if my Schumacher Electric SE-125A has no reading on the ammeter?
If your Schumacher Electric Battery Charger shows no reading on the ammeter, several issues could be the cause. First, ensure the charger is properly plugged into a working AC outlet with no blown fuse or tripped circuit breaker. Check that the clips are making good, clean connections to the battery and frame; rocking them back and forth can help. Also, verify the connections are not reversed. If these steps don't resolve the issue, the battery itself may be defective or the 2 amp charge rate is being used (ammeter may show no activity at the 2A charge rate).
General| Type | Automatic |
|---|---|
| Input Voltage | 120V AC |
| Weight | 12.3 lb |
| Dimensions | 12.5 x 8.5 x 5.5 inches |
| Cable Length | 6 ft |
| Output Voltage | 12V |
| Battery Type | AGM |
| Battery Compatibility | 12V |
| Safety Features | Overcharge protection |
| Charging Current | 2/12/25A |
| Charger Type | Smart Charger |
