SCRAM Systems SCRAM CAM

Questions and Answers

T
Tyler BondAug 3, 2025
What to do if my SCRAM Systems SCRAM CAM Measuring Instruments bracelet battery is draining quickly?
- J
  Jennifer SuttonAug 3, 2025
  If you're experiencing quick battery drain or low battery alerts with your SCRAM Systems Measuring Instruments bracelet, first, find out if the client has been waking up the bracelet too much with a magnet. Inspect the bracelet for any signs of water damage. Try replacing the battery with a fresh one from a new, unopened package. If the low battery alert comes back before the next scheduled maintenance, contact AMS.
J
Jesse MilesAug 10, 2025
What to do if SCRAM Systems Measuring Instruments detects alcohol during installation?
- D
  Denise FoxAug 10, 2025
  If alcohol is detected during the installation of your SCRAM Systems Measuring Instruments bracelet, make sure that no sanitizers or cleaners other than water or Sporicidin are being used on the bracelet or client. Perform a breathalyzer test to confirm that the client hasn't been drinking. You can also try replacing the faceplate, performing observed readings, and using Direct Connect on the bracelet. Assigning another bracelet is also an option. If alcohol is still detected, the client may be emitting alcohol or there could be an interferant on the client or installer.
J
johnallenAug 15, 2025
What to do if SCRAM Systems Measuring Instruments bracelet will not communicate with base station?
- M
  Mark MyersAug 16, 2025
  If your SCRAM Systems Measuring Instruments bracelet isn't communicating with the base station, instruct the client to read information from base station. Verify that the base station serial number matches the one displayed on the client’s Equipment page. Try waking the bracelet with a magnet to see if the base station starts reading information. If not, perform a hard reset: remove the battery, hold a magnet on the upper-left corner of the bracelet, and reinsert the battery. If problems persist, contact AMS.
L
Larry CamposAug 21, 2025
How to clean build up inside SCRAM Systems SCRAM CAM Measuring Instruments bracelet?
- K
  kimberly31Aug 21, 2025
  To address buildup inside your SCRAM Systems Measuring Instruments bracelet: make sure the client knows how to properly clean under the bracelet. Determine if the buildup is intentional or due to hygiene issues. Remove the bracelet and straps. Clean the pogo pins with a toothbrush and a lint-free cloth. Then, reinstall the straps and bracelet on the client.
M
Marilyn YatesAug 27, 2025
How to fix SCRAM Systems Measuring Instruments bracelet that will not power up?
- B
  Bailey DicksonAug 27, 2025
  To fix a SCRAM Systems Measuring Instruments bracelet that won't power up (no green light), replace the bracelet battery. Then, reset the bracelet by removing the battery, holding a magnet on the upper-left corner, and reinserting the battery. If it still doesn't power on, contact AMS.

Summary

Initial SCRAM CAM;SCRAM CAM+HA Client Setup

Add New Client in SCRAMNET

Procedure for entering new client information into the SCRAMNET system.

Assign SCRAM Equipment - CAM Client

Steps for assigning SCRAM CAM equipment to a client monitored for alcohol abstinence only.

Assign SCRAM Equipment - CAM+HA Client

Steps for assigning SCRAM CAM equipment to a client monitored for alcohol abstinence and house arrest.

Assign SCRAM Equipment - Remote;Jail

Ongoing Client Management Procedures

Replace SCRAM CAM Bracelet

Detailed instructions for replacing a SCRAM CAM bracelet with a new one.

Assign SCRAM Base Station

Replace SCRAM Base Station

Remove SCRAM Base Station

Replace Battery in SCRAM CAM Bracelet

Steps for replacing the battery within the SCRAM CAM bracelet.

Perform SCRAM CAM Bracelet Hard Reset

Supervision Modification

Add House Arrest to Existing CAM Client

Closing Tasks

Check In SCRAM Equipment

Clean;Disinfect SCRAM Equipment

Troubleshooting SCRAM Equipment

Bracelet will not power up;no green light

Action steps for when the SCRAM bracelet fails to power on or show a green light.

Bracelet will not communicate with base station

Recommended actions when the bracelet fails to communicate with the base station.