Scrib3D Advanced - User Manual

User Manual
Scrib3D
Advanced
For the best user experience,
please read this manual completely
before usage.
www.Scrib3Dpen.com
Getting Started
DC 5V/2A
Once the temperature indicator Light has changed from red to
green you can load lament into the 3D pen. Straighten the
lament at the end. Press and hold the Feed Button. Push the
lament into the pen until you can feel it pulling it into the pen.
The Display will ash either ABS or PLA until the Forward Button is
pressed to chose a mode. Then the screen will show desired
temperature and current temperature. The temp LED will remain red
while the pen is heating up. Once it has reached temp it will change to
Green. Then you can draw. You can adjust the temperature at any time
but to change from ABS to PLA unplug the pen and plug it back in.
1. Power On
Plug the USB power cord into the power
adapter and connect it to an outlet. Plug the
other end of the power cord into your pen.
(Note: this 3D Pen can be used with a 3rd party
power bank with at least 2 Amps output)
2. Select the Filament
“ABS” or “PLA” will show on the LCD SCREEN,
you can use the temperature ADJUSTER buttons
to select a mode. Choose a mode that
corresponds with the type of plastic you are
using. (Note: Using the wrong plastic will make
for a poor experience and possibly damage
your pen)
3. Temperature Settings
Press the FORWARD button to activate the
selected mode. You can use the TEMPERATURE
ADJUSTER buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
180-210°C and PLA: 160-180°C.
4. Filament Loading & Drawing in 3D
Once the desired temperature has been
reached the LED on the pen will turn green. You
can click the FORWARD button. Straighten the
end of the lament you wish to use and load it
into the FILAMENT LOADER while the pen is
running. Once plastic starts extruding
you are ready to start creating in 3D!
5. Changing Colors
To change colors, press and hold the REVERSE
button for 5 seconds. The lament will
automatically start to retract out of the back of
the pen.
1. Power On
Plug the USB power cord into the power
adapter and connect it to an outlet. Plug the
other end of the power cord into your pen.
(Note: this 3D Pen can be used with a 3rd party
power bank with at least 2 Amps output)
2. Select the Filament
“ABS” or “PLA” will show on the LCD SCREEN,
you can use the temperature ADJUSTER buttons
to select a mode. Choose a mode that
corresponds with the type of plastic you are
using. (Note: Using the wrong plastic will make
for a poor experience and possibly damage
your pen)
3. Temperature Settings
Press the FORWARD button to activate the
selected mode. You can use the TEMPERATURE
ADJUSTER buttons to ne tune the
temperature depending on need and desired
usage. The temperature ranges are ABS:
180-210°C and PLA: 160-180°C.
4. Filament Loading & Drawing in 3D
Once the desired temperature has been
reached the LED on the pen will turn green. You
can click the FORWARD button. Straighten the
end of the lament you wish to use and load it
into the FILAMENT LOADER while the pen is
running. Once plastic starts extruding
you are ready to start creating in 3D!
5. Changing Colors
To change colors, press and hold the REVERSE
button for 5 seconds. The lament will
automatically start to retract out of the back of
the pen.
PLA
170
W ARNI N G S
The Scrib3d Advanced should only be used with ABS,
PLA filament approved by Scrib3d. Misuse of your
Scrib3d Advanced , setting your pen to the wrong
heating temperature, and/or use of non-approved
plastics or other materials may result in damage to your
pen or injury to you, and will void your warranty. Injuries
to the user may include, but are not limited to, harm
sustained from inhaling substances that are not suitable
for heating; or burns from flammable materials used in
the Scrib3d Advanced .
DO NOT use the Scrib3D Advanced near bathtubs,
showers, basins or other vessels containing water.
This could result in death due to electric shock.
Allow the Nozzle to cool completely before storing.
Unplug and set the Control Switch to OFF when not in
use or before storing.
- The Nozzle of the Scrib3D Advanced can become
hot. DO NOT touch the Nozzle, or you may be burned!
- DO NOT allow the Nozzle near or in contact with
flammable materials.
- Inform others in the area that the Pen is hot and
should not be touched.
This 3D Printing Device - when used with a styrene
filament (ABS / HIPS / or PC-ABS) - can expose you and
others in the same room to styrene, which is a chemical
known to the State of California to cause cancer. For more
information, go to www.P65Warnings.ca.gov. ALWAYS
OPERATE YOUR 3D PRINTING DEVICE IN A
WELL-VENTILATED AREA.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.5A MAX, 50-60Hz Output: +5V DC, 2A
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to use your
Scrib3d Advanced, please refer to our website: Scrib3dPen.com
To troubleshoot, please visit: Scrib3dPen.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
scrib3dpen.com/warranty
For Scrib3D Terms and Conditions and other notices refer to our
website: scrib3dpen.com/terms-and-conditions
This marking indicates that this product should not be
disposed of with other household wastes. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
FILAMENT
LOADER
POWER
TEMPERATURE
ADJUSTER
REVERSE
FORWARD
NOZZLE
SPEED
ADJUSTER
LCD SCREEN
LED:
POWER
INDICATOR
LED:
TEMP
INDICATOR
Product Overview
5V 2Amp PLA Filament1 Scrib3D
ADVANCED Pen

Summary

Safety Warnings

Hot Surface and Flammable Material Precautions

Warns about the hot nozzle and keeping it away from flammable materials.

Electrical Shock and Water Hazard Warnings

Advises against using the device near water to prevent electric shock.

Material Compatibility and Health Advisory

Specifies approved filaments, warns of misuse, and notes health advisories.

Getting Started Guide

Powering On the Device

Instructions for connecting the power adapter and plugging in the pen.

Filament Type Selection

How to select 'ABS' or 'PLA' mode using temperature adjuster buttons.

Temperature Adjustment

Guidance on activating modes and fine-tuning temperature for ABS and PLA.

Loading Filament and 3 D Drawing

Steps for loading filament and starting to create in 3D once heated.

Changing Filament Colors

Procedure to retract filament by holding the REVERSE button.

Usage Tips and Best Practices

Drawing Angle and Surface Adhesion

Recommends a 65-degree angle for drawing flat objects and on surfaces.

Filament Preparation and Loading

Tips on cutting filament ends flat for smooth insertion and preventing jams.

Filament Removal and Swelling

Advises using the REVERSE button for removal and handling swollen filament.

Filament Quality and Storage

Recommends using Scrib3D filament and storing it sealed and dry.

Plastic Oozing Phenomenon

Explains plastic oozing after stopping and suggests decreasing temperature.

Troubleshooting Common Issues

Power Indicator Not On

Solutions for power issues related to adapter, plug, or pen electronics.

Red and Green Indicator Light Flashing

Addresses issues with low-power adapters or power banks.

No Filament Extrusion

Troubleshoots when nothing comes out of the nozzle, including temp and mode settings.

Pen Not Heating Up or Motor Struggling

Solutions for heating element/nozzle problems or motor issues.

Error Display and Filament Jams

Addresses 'ERR' messages and filament jams due to stripped or swollen parts.

Overview

1. Function Description
2. Usage Features
3. Maintenance Features

This document describes the Scrib3D Advanced 3D Pen, a device designed for creating three-dimensional objects by extruding heated plastic filament. It functions similarly to a glue gun but with greater precision and control, allowing users to draw in the air or on surfaces.

Function Description

The Scrib3D Advanced 3D Pen operates by heating plastic filament to a molten state, which is then extruded through a nozzle. As the plastic cools rapidly upon exiting the nozzle, it solidifies, allowing users to build up layers and create 3D structures. The pen supports two main types of plastic filament: ABS and PLA, each requiring specific temperature settings for optimal performance.

The pen features an LCD screen that displays the selected filament type (ABS or PLA) and the current temperature. Users can select the appropriate mode using the temperature adjuster buttons. Once the desired temperature is reached, indicated by a green LED light, the pen is ready for use. Filament is loaded into the FILAMENT LOADER while the pen is running, and plastic begins to extrude when the FORWARD button is pressed.

For changing colors or removing filament, the REVERSE button is pressed and held for 5 seconds, which automatically retracts the filament from the back of the pen. This feature is crucial for preventing jams and ensuring smooth operation. The pen is designed for adult use and should be kept out of reach of children due to the hot nozzle and potential for misuse.

Usage Features

The Scrib3D Advanced 3D Pen offers several features to enhance the user experience:

• Filament Selection: Users can choose between ABS and PLA modes via the LCD screen and temperature adjuster buttons. Selecting the correct filament type is essential for proper operation and to avoid damaging the pen.
• Temperature Adjustment: The pen allows for fine-tuning of the temperature using the TEMPERATURE ADJUSTER buttons. This flexibility enables users to optimize extrusion based on their specific needs and desired usage, within the recommended ranges for ABS (180-210°C) and PLA (160-180°C).
• Filament Loading and Extrusion: After the pen reaches the desired temperature (indicated by a green LED), users can straighten the end of the filament and load it into the FILAMENT LOADER. Pressing the FORWARD button initiates plastic extrusion, allowing for 3D creation.
• Filament Retraction: To change colors or remove filament, pressing and holding the REVERSE button for 5 seconds will automatically retract the filament. This is a critical step to prevent filament from swelling and causing jams within the pen.
• Ergonomic Design: The pen is designed for comfortable use, with optimal results achieved by holding it at an angle of 65 degrees or higher, especially when drawing flat objects or on surfaces.
• Power Source Flexibility: The pen can be powered by a standard USB power cord connected to an adapter and outlet. Additionally, it can be used with a 3rd party power bank that provides at least 2 Amps output, offering portability.
• Safety Sleep Mode: The pen automatically enters sleep mode after 5 minutes of inactivity as a safety feature. Any button press will wake it up and restart the heating sequence.
• Visual Indicators: LED lights indicate power status, temperature readiness (red for heating, green for ready), and the LCD screen provides clear information on filament mode and temperature.

Maintenance Features

Proper care and maintenance are crucial for the longevity and optimal performance of the Scrib3D Advanced 3D Pen:

• Nozzle Safety: The nozzle becomes hot during operation. Users are warned not to touch it to avoid burns and to keep it away from flammable materials. It is important to inform others in the area that the pen is hot.
• Cool-Down Procedure: After use, the pen should be unplugged, the control switch set to OFF, and allowed to cool completely before storing.
• Filament Management: Only Scrib3D-approved ABS and PLA filament should be used. Misuse, incorrect temperature settings, or using non-approved plastics can damage the pen and void the warranty.
• Filament End Preparation: Before inserting a new strand or changing plastic, ensure the filament end has a flat surface. Failure to do so can lead to jams or prevent proper extrusion. If filament is partially withdrawn and swells, it should be fully withdrawn, and the swollen part cut off.
• Filament Storage: To maintain filament quality, it is recommended to store Scrib3D filament in a sealed and dry location.
• Troubleshooting Guidance: The manual provides a comprehensive troubleshooting section for common problems such as the power indicator not turning on, indicator lights flashing, no extrusion, pen not heating up, motor struggling, or "ERR" displayed. Solutions range from checking the AC adapter and power bank to adjusting temperature, preparing filament ends, or replacing the nozzle.
• Environmental Considerations: The product is marked for proper disposal, indicating it should not be disposed of with household waste. Users are encouraged to recycle it responsibly to promote sustainable reuse of materials.
• Ventilation: When using styrene filament (ABS/HIPS/PC-ABS), which can expose users to styrene (a chemical known to cause cancer), it is crucial to ALWAYS OPERATE THE 3D PRINTING DEVICE IN A WELL-VENTILATED AREA.
• Cleaning: While not explicitly detailed, the general principle of keeping the device clean and free from plastic residue around the nozzle area would contribute to its longevity. The retraction feature helps prevent plastic from solidifying inside the pen, which is a common cause of maintenance issues.

Scrib3D Advanced Specifications

General

Nozzle Diameter	0.4 mm
Filament Diameter	1.75 mm
Technology	FDM (Fused Deposition Modeling)
Materials	PLA, ABS
Connectivity	USB, SD Card