What causes abnormal noise from Sea-doo Boat propulsion system?
Abnormal noise from the Sea-doo Boat propulsion system can be caused by weeds or debris jammed around the impeller, or a damaged impeller shaft or drive shaft. Clean and check for damage.
Why Sea-doo Boat has weak spark?
If the Sea-doo Boat has a weak spark, it could be due to fouled, defective, or worn spark plugs, or too much oil supplied to the engine. Replace the spark plugs.
Why Sea-doo Boat beeps 1 long beep?
The Sea-doo Boat beeps once for a long time because the safety lanyard has been on the post for more than 10 minutes without starting the engine, there's a bad connection, the wrong safety lanyard is being used, the safety lanyard is defective, dried salt water is in the safety lanyard cap, or there's an improper operation of MPEM or a defective wiring harness. Apply slight pressure or remove and reinstall the safety lanyard. Reinstall the safety lanyard cap correctly over the post. Use a safety lanyard programmed for the watercraft. Clean the safety lanyard cap to remove salt water.
What does 1 second beep every second mean on Sea-doo Boat?
If your Sea-doo Boat (DI model) beeps every second, the engine drowned mode is active. Release the throttle to cancel this mode.
What does 2 seconds beep every minute mean on Sea-doo Boat?
General| Manufacturer | Sea-Doo |
|---|---|
| Model | GTX RFI |
| Category | Personal Watercraft |
| Engine Type | 2-Stroke |
| Fuel System | RFI (Rotax Fuel Injection) |
| Seating Capacity | 3 |
| Oil Capacity | 3.2 quarts |
Provides essential rules and precautions for safe watercraft operation.
Details on how to operate the watercraft safely, including passenger safety.
Details the duration of the warranty for different usage types.
Explains the manufacturer's responsibilities for repairs under warranty.
Outlines the customer's obligations for warranty service validation.
Lists conditions and damages not covered by the limited warranty.
Details the duration of the warranty for different usage types globally.
Explains manufacturer's responsibilities for repairs under international warranty.
Outlines customer obligations for international warranty service validation.
Lists conditions and damages not covered by the international limited warranty.
Location and composition of the Hull Identification Number.
Details on locating the Engine Identification Number for various engine types.
Explanation of safety lanyard, DESS, and engine start/stop button functions.
How to use the handlebar and throttle lever for watercraft control.
Description of fuel gauge, speedometer, tachometer, and info center.
Details on fuel tank valve, cap, and oil injection reservoir.
Information on eyelets, cleats, boarding aids, cooling, and jet pump.
Covers the location and function of fuses and the battery.
Step-by-step guide for safe and proper watercraft fueling.
Specifies the correct types of fuel and oil for the watercraft.
Recommended inspection after the initial 10 hours of operation.
Explains the basic propulsion mechanism of the watercraft.
Detailed steps for safely starting the watercraft engine.
Guidance on riding, crossing waves, and handling different conditions.
Instructions on how to slow down, stop, and dock the watercraft.
Methods for safely boarding the watercraft from docks or deep water.
Steps for daily cleaning, draining water, and flushing the cooling system.
Methods to protect metallic components from corrosion.
Troubleshooting steps for engine overheating and cleaning the intake.
Procedures for dealing with engines affected by water or fuel flooding.
Guidance on towing the watercraft and addressing low-charge battery conditions.
Details on manufacturer and dealer responsibilities for emission systems.
Instructions for lubricating various moving parts and components.
A schedule for regular checks and servicing of the watercraft.
Guidelines and safety precautions for towing the watercraft.
Steps for preparing and storing the watercraft for the off-season.
Instructions for getting the watercraft ready for use after storage.
Interpreting beeper signals to diagnose system issues.
Common causes and remedies for the engine not starting.
Diagnosing and resolving issues like misfires, overheating, and low power.
To Next Page
