EasyManua.ls Logo

sebra 2600 - User Manual

sebra 2600
50 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
operation manual
108731-IE
Model 2600
OMNI™ Sealer
Power Source
VANTE INC
IGNITING INNOVATION

Table of Contents

Questions and Answers

  • K
    keith37Aug 4, 2025
    Why is my sebra 2600 Portable Generator arcing or producing bad seals?
    • Z
      zdennisAug 4, 2025
      Arcing or bad seals in your Sebra Portable Generator can occur due to several reasons. The sealing area might be contaminated, so you should clean the sealing jaws. Moisture in the sealing area or on the tubing can also cause this issue, so ensure the tubing's exterior, the sealing region, and adjacent areas are clean and dry. If you're using a hand-held lever, make sure you're not releasing it prematurely; wait until the sealing indicator light is off. Ensure the sealing head is being used properly and that you are using tubing for blood and blood products (usually PVC). Also, ensure the sealing head jaws close evenly.
  • C
    Christopher HaysAug 18, 2025
    What to do if my sebra 2600 is not sealing?
    • R
      Rhonda BriggsAug 18, 2025
      If your Sebra Portable Generator isn't sealing, several factors could be at play. First, check that the power source is correctly connected and that the AC power switch is in the '|' (on) position with the RF ready light illuminated. If you're using a Hand-Held Sealing Head, consider replacing the Model 1103 RF cable if there is a RF cable malfunction. Also, ensure the fuse(s) is (are) not blown, replace if needed.

Summary

Consumer Information

Proprietary Rights

Details manual content ownership, Vante trademarks, and copyright information.

Disclaimer

Outlines safe usage, operator responsibilities, and warranty voidance for improper use.

Chapter 1: Introduction

Preliminary Information

Covers document scope, intended audience, and proprietary information details.

Symbols

Explains document and device symbols for clear communication and safety.

Device Specifications

Provides physical, electrical, and environmental specifications for the Model 2600.

Chapter 2: Product Description

Product Overview

Introduces the Vante SEBRA Model 2600 OMNI Sealer and its system components.

Theory of Operation

Explains how RF energy is utilized for dielectric heating and sealing of tubing.

Application

Details the primary use of the device in blood banking and transfusion centers.

Component Identification

Identifies and describes the various components of the sealing system.

Operating Environment

Specifies optimal environmental conditions for operation and storage.

Sealing Applications

Lists recommended tubing and applications for different sealing heads.

PVC Tubing Size Categories

Categorizes PVC tubing by size, wall thickness, and examples of use.

Seal Cycle

Defines the seal cycle, maximum seals per hour, and cooling procedures.

Chapter 3: Power Source Operation

Setup

Guides users through unpacking, connecting power, and initial setup.

Sealing Procedure with Model 1105 Hand-Held Sealing Head

Step-by-step instructions for performing seals with the hand-held head.

Sealing Procedure with Model 2605 Bench-Top Sealing Head

Step-by-step instructions for performing seals with the bench-top head.

Seal Spacing

Provides guidelines for spacing multiple seals on tubing for integrity.

Chapter 4: Maintenance

Cleaning Omni Power Source Case

Instructions for cleaning the exterior of the power source unit safely.

Troubleshooting

Offers solutions for common problems, including diagnosis and actions.

Chapter 5: Failure Isolation

Failure Isolation

Methodology for identifying the root cause of system malfunctions.

Fuse Replacement

Detailed steps for safely replacing fuses in the power source unit.

Customer Service

Information on training, repair services, and product return procedures.

Chapter 6: Radio Frequency System Safety Considerations

General Information

Overview of RF use in Vante instruments and general safety advice.

RF Effects on Human Tissue

Warns about potential RF burns from direct contact with electrodes.

RF Effects on Pacemakers

Addresses the safety of Vante instruments concerning cardiac pacemakers.

Electrical Safety

Ensures safe electrical operation and protection against shock hazards.

RF Effects on Electronic Equipment

Discusses potential interference with nearby electronic devices.

RF Effects in Potentially Explosive Atmospheres

Prohibits use in explosive environments due to arcing risks.

Chapter 7: Reference Information

Appendix A: EMC Standard Requirements

Specifies EMC standards and guidance for device operation.

Operation Precautions

Advises on approved accessories and proper operating environment.

Electromagnetic Immunity

Details the intended electromagnetic environment for the device.

sebra 2600 Specifications

General IconGeneral
Fuel TypeGasoline
Power Output120V
Engine Type4-Stroke OHV
Run Time at 50% Load8 hours
Noise Level68 dBA
Outlet Types2 x 120V 20A Outlets, 1 x 12V DC Outlet