SECO-LARM Enforce SK-1131-SQ User Manual

Digital Access Keypad Manual
MT_SK-1131-SQKeypad092810.pmd
®
PIHAK1
SECO-LARM U.S.A., Inc.
Digital Access Keypad with 3 Outputs
®®
SECO-LARM
Note: Model numbers that end with "Q" or that have a round green "Q" sticker signify RoHS-compliant products.
SK-1131-SQ
MANUAL
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: sales
@ seco-larm.com
LIFETIME LIMITED WARRANTY
This SECO-LARM product is warranted against defects in material and workmanship while
used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the repair or replacement of any defective part
if the unit is returned, transportation prepaid, to SECO-LARM. Under no circumstances will SECO-LARM be responsible for any costs or
charges for removal, installation, or reinstallation. This Warranty is void if damage is caused by or attributed to acts of God, physical or
electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products sold and installed in the United States
and Canada. For all other countries the warranty is 1 (one) year.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2010 SECO-LARM U.S.A., Inc. All rights
reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
User Operation for the SK-1131-SQ
1. Using the User Codes:
A. User codes operate the door (4-8 digits long).
Press
B. The key must be pressed also if the keypad is in manual-entry mode.
Press
2. Using the Master Code:
The Master Code can be used to operate any output.
Press (Relay output #1)
Press (Relay output #2)
Press (Relay output #3)
3. Using the Inhibit/Lockout Code:
Please contact your installer for an explana ion of inhibit mode and its operation.
4. Using Duress Codes:
For a full explanation of duress codes and their uses, see pg. 12.
5. Delete/Add/Change User and Master Code:
A. Enter the Master Code first, followed by the key
(If you forgot the master code, see page 15 for more information.
Press
B. Changing/Adding Users:
Press 00-99 (user ID) (user code, 4-8 digits) (for relay output #1)
Press 0-9 (user ID) (user code, 4-8 digits) (for relay output #2)
Press 0-9 (user ID) (user code, 4-8 digits) (for relay output #3)
C. Deleting Individual Users:
Press 00-99 (user ID) (for relay output #1)
Press 0-9 (user ID) (for relay output #2)
Press 0-9 (user ID) (for relay output #3)
D. Changing the Master Code:
Press
E. To exit programming mode, press the key.
®
ENFORCER
SK-1011-SQ SK-2323-SDQ
SK-3123-SDQ
Indoor Keypad
Outdoor Keypads
Also available from SECO-LARM:
SK-1123-SQ SK-1123-FQ
X X X X
X X X X
X X X X
X X X X
*
*
#
#
#
#
#
#
1
1
1
3
0
*
#
X X X X
#
2
u u u u
u u u u
u u u u
2
3
#
u u u u
#
u u u u
#
2
#
3
Note: indicates
the user code.
Note: indicates
the master code.
u u u u
X X X X
Page 16

SECO-LARM Enforce SK-1131-SQ Specifications

General

Type	Keypad
Dimensions	4-1/2" x 3-1/8" x 1-1/4" (115 x 80 x 32 mm)
Weatherproof	Yes
Weather Resistance	IP65
Egress Input	Yes
Operating Temperature	-4°~158° F (-20°~70° C)
Number of Buttons	12
Backlight	Yes
Power Supply	12~24 VDC/AC
Operating Voltage	12~24 VDC/AC

Summary

User Operation Guide

Using User Codes

Explains how to use user codes for door operation and keypad entry.

Using the Master Code

Details how to use the master code to operate any output.

Using Inhibit/Lockout Code

Refers to installer for explanation of inhibit mode and its operation.

Using Duress Codes

Directs to page 12 for a full explanation of duress codes and their uses.

Manage User and Master Codes

Instructions for managing user and master codes, including deletion and changes.

Keypad Reprogramming and Bypass

Reprogram Keypad (Certain Data)

Procedure to change specific data in the keypad, such as user codes.

Reprogram Keypad (Complete Data Refresh)

Process to erase all current data except the master code for a complete refresh.

Delete User Access

Steps to remove a user's access code from the keypad.

Master Code Bypass (DAP Jumper)

How to bypass a forgotten master code using the DAP jumper.

Installer and Feature Details

Installer Programming Functions

Configuration options for professional installers.

Keypad Unique Features

Overview of special functionalities like mantrap, inhibit control, and warnings.

Wiring and Programming Preparation

Wiring - Basic Diagram

Provides a visual representation of the keypad's wiring connections.

Preparing to Program Keypad

Information needed before starting keypad programming.

Adding or Changing User Codes

Instructions for adding new user codes or changing existing ones.

Programming Notes and Specifications

Programming Notes

Important considerations for master code, defaults, and code operations.

LED Indicators

Explanation of the functions of the Green and Red LEDs.

Buzzer and LED Signals

Table detailing buzzer tones and LED flashes for different keypad statuses.

Technical Specifications

Detailed technical data including power, outputs, inputs, and dimensions.

Advanced Wiring Examples

Wiring with Inhibit Control Authorized

Diagram illustrating wiring for inhibit control authorization.

Wiring Auxiliary Accessories

Diagram showing connections for auxiliary accessories like tamper and duress.

Specific Wiring Configurations

Wiring for Mantrap Using Two Keypads

Diagram for wiring two keypads to implement the mantrap feature.

Wiring for Lock Device and Alarm Arm/Disarm

Diagram showing connection to lock device and alarm control panel.