Seko TEKNA TPR 600 User Manual

Control Panel – TEKNA TPR
Access to the programming menu
When pressed during the pump operation phase, it cyclically displays the programmed values on
the display; When pressed at the same time as the
keys, it increases or lowers a value
dependent on the selected operating mode. During programming it carries out an “enter” function,
meaning that it confirms entry to the various menu levels and modifications within the same.
Starts and stops the pump. In the event of a level alarm (alarm function only), flow alarm and active
memory alarm, it deactivates the signal on the display.
Used to “exit” the various menu levels. Before definitively exiting the programming phase, you will be
asked if you wish to save any changes.
Access to the pump calibration menu. If in Off mode, the calibration menu is not activated.
Used to run upwards through the menu or increase the numerical values to be changed. Can be
used to start dosage in Batch mode
Used to run downwards through the menu, or decrease the numerical values to be changed.
Flashing green LED during dosage
Red LED that lights up in various alarm situations
Electrical connections
1
2
Alarm relay
3 Pole +
4 Pole -
Exit 4-20 mA
500 Ω max load
5
6
Remote control input (start-stop)
7
8
Temperature probe input
9
10
Flow sensor input
B
B Input level control
EM00136063 rev. 1.0
1

Seko TEKNA TPR 600 Specifications

General

Brand	Seko
Model	TEKNA TPR 600
Category	Laboratory Equipment
Language	English

Summary

Control Panel Overview

PROG, Mode/Enter, Start/Stop, ESC, CAL, and Arrow Button Functions

Details the primary functions of the control panel buttons for programming, operation, and navigation.

LED Indicators and Alarm Signals

Explains the meaning of the green LED for dosage and the red LED for alarm situations.

Electrical Connection Terminals

Lists and describes the terminal connections for alarm relay, I/O, sensor inputs, and level control.

Programming Menu and Navigation

Entering the Programming Menu

Instructions on how to access the programming menu using the PROG key.

Main Menu Configuration Options

Overview of the main menu structure and key configuration parameters available.

Setting Menu Parameters

Details the parameters adjustable within the Setting Menu, such as flow rate and language.

Functions Menu Selection

Explains how to select measurement functions like pH or Redox measurement.

Setting the Language

Language Selection Process

Describes how to change the pump's display language using the control panel.

Manual Dosage Operation

Constant Mode Flow Regulation

Details how the pump operates in constant mode and how to manually adjust flow rate.

Proportional pH Dosage Programming

Setpoint and Type Configuration

Configuring the target pH value and setpoint type (acid/alkaline).

Proportional and Alarm Band Settings

Setting the proportional band and alarm band for pH control.

O.F.A. and Resolution Setup

Setting the Over Feed Alarm time and measurement resolution.

Probe Calibration and Temperature

Procedures for probe calibration and manual temperature input.

Proportional Redox Dosage Programming (O.R.P.)

Setpoint and Type Configuration (Redox)

Configuring the target Redox value and setpoint type (high/low).

Proportional and Alarm Band Settings (Redox)

Setting the proportional band and alarm band for Redox control.

O.F.A. and Probe Calibration (Redox)

Setting Over Feed Alarm time and probe calibration for Redox measurements.

Setting the Maximum Flow Rate

Maximum Flow Rate Configuration

Setting the pump's maximum flow rate and the display unit for flow.

Setting the Alarm Relay

Alarm Relay Configuration Options

Setting the alarm relay to be open (default) or closed during alarm situations.

Flow Calibration Procedures

Manual Flow Calibration

Manually calibrating flow by entering the cc/stroke value.

Automatic Flow Calibration

Performing automatic flow calibration using pump strokes and measured volume.

Pump Statistics and Reset

Viewing Pump Statistics

Accessing statistics like operation time, strokes, quantity dosed, and power.

Resetting Operation Counters

How to reset the pump operation counters for statistics.

Password Protection and Access

Password Setting and Management

Setting, using, and eliminating the password for menu access and modification.

Flow Alarm Configuration

Flow Sensor Activation and Signals

Activating the flow sensor and configuring the number of signals for alarm triggers.

Level Alarm Configuration

Level Alarm Behavior Settings

Configuring whether to stop dosage or just signal an alarm when the level sensor is activated.

Flow Display Unit Configuration

Display Unit Selection for Flow

Selecting the display unit for flow measurement (L/h, Gph, ml/m, or %).

pH Calibration Procedures

Automatic pH Calibration Steps

Step-by-step guide for performing automatic pH calibration.

Manual pH Calibration Steps

Guide for manual pH calibration, including user-inputted values.

Redox Calibration Procedures (O.R.P.)

Automatic Redox Calibration Steps

Step-by-step guide for performing automatic Redox calibration.

Manual Redox Calibration Steps

Guide for manual Redox calibration, including user-inputted values.

Alarm Types and Troubleshooting

Level Alarms (Lev)

Details on Level alarm display, cause, and interruption to pump operation.

Memory Alarms (Mem)

Details on Memory alarm display, cause, and interruption from external impulses.

Flow Alarms (Flw)

Details on Flow alarm display, cause, and interruption due to sensor signals.

Parameter Error and O.F.A. Alarms

Troubleshooting for parameter errors and O.F.A. alarms.

Measurement (Aim) and Calibration (Cal) Alarms

Troubleshooting for measurement outside band and probe not calibrated alarms.