Sencor SSI 6100GR - Page 7

- 4 -
11/2023
2023, .
Note:
When used for the first time, the iron may emit smoke,
which is non-toxic. You may also hear noises created by
expanding plastics. This is normal. After ashort time, the
iron will stop emitting smoke and making noises.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRONING WITH STEAM
Attention:
In order to iron with steam, the water tank must be
filled with water.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTINUOUS STEAMING FUNCTION
• For iron with steam, slide the steam release regulator from position
towards position . Set the position of the regulator based on the
required steam intensity. The more the steam regulator is moved to
the right, the stronger the steam intensity.
• Wait until the heating indicator turns off.
• The steam release regulator can be moved at any time while ironing.
• For all standard ironing, it is recommended to use the middle settings
of the steam release regulator. Only when ironing linen fabrics, strong
silk or similar fabrics is it recommended to set the steam release
regulator to maximum.
Note:
The iron continuously emits steam only when you keep
moving it. When putting the iron down in a vertical position,
we recommend turning off the steam output using the
steam output regulator.
• Setting the steam release regulator to position
, deactivates the
steam function.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEAM IMPULSE FUNCTION
• Use this function when ironing with continuous steam is insufficient.
Press the steam impulse button
to generate astrong flow of steam,
which can straighten out even very crumpled up textiles.
• Wait at least 3 seconds before pressing the button again. If the heating
indicator starts flashing, wait until it turns off and only then press the
button.
• The steam impulse function can also be used when ironing hanging
textiles (e.g. curtains, garments hanging on coat hangers, etc.). Use
one hand to gently tension the fabric and vertically move the iron from
bottom up. Press the steam impulse button to achieve vertical bursts
of steam. Do not hold the steam impulse button continuously and do
not consecutively use it more than 10 times.
Attention:
Do not use the steam function for silk and synthetics
so as not to damage the fabric.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WATER SPRAYING FUNCTION
• The water spraying function can be used with any ironing method. It
serves to moisten the fabric and effectively helps with ironing heavily
crumpled textiles.
• Make sure that there is asufficient amount of water in the water tank
and turn the iron so that its front side points towards the location that
you wish to spray.
• Press the water spraying button
. Water will spray out of the nozzle
on the front side.
Note:
When using the water spraying function for the first time or
when you have not used the iron for along time, it will be
necessary to press the water spraying button several times
before the nozzle starts working correctly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRIP-STOP SYSTEM
• The iron is equipped with the Drip-Stop system, which automatically
stops water supply when the set temperature is insufficient for
generating steam and thereby prevents potential dripping of hot water
out of the steam outlets.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANTI-CALC SYSTEM
• This iron is equipped with apermanent Anti- Calc filter, which limits
the formation of limescale deposits inside the iron. This filter cannot be
deactivated. The effectiveness of the filter depends on the hardness of
the water used.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURNING OFF
• Stand the iron upright and set the steam release regulator to position
.
• Set the temperature control knob to the MIN position.
• Disconnect the power cord from the power socket and allow the
soleplate to cool down. After the soleplate has cooled down, clean
the iron according to the instructions in chapter Cleaning and
maintenance.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIPS FOR QUALITY IRONING
• If you are ironing fabrics from blended materials (e.g. 40% wool
and 60% synthetic material), set the temperature according to the
material which is ironed at alower temperature.
• If you do not know the composition of the fabric, identify the suitable
temperature setting by ironing apiece of the fabric from the underside.
Start by setting alow temperature and gradually increase it until the
ideal temperatures is achieved.
• Never iron over places that have sweat marks or other stains. The high
temperature fixes the stain in place, making it difficult to remove.
• To avoid silk, wool and synthetic fabrics from being shiny after ironing,
iron them from the underside.
• Some materials are easier to iron when they are lightly damp.
• Spray fine fabrics before ironing them or iron them under alightly
dampened wiping cloth.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE
Cleaning after every use
Attention:
Before cleaning, the iron must be disconnected from
the power socket and cooled down.
Do not submerge the iron in water when cleaning it.
• Open the water tank cap and empty out the remaining contents of the
water tank over asink. Close the cap.
• In the event that the soleplate or the surface of the iron is dirty, wipe
with alightly dampened cloth and then wipe dry.
• For cleaning, do not use steel wool, solvents or cleaning products with
an abrasive effect, etc. to prevent damaging the surface being cleaned.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING LIMESCALE DEPOSITS
• For the removal of limescale deposits from the inner part of the
soleplate, the iron is equipped with aself cleaning function. Use this
function regularly at least once every 14 days.
• Fill the water tank with clean water up to the maximum water level
mark. Connect the iron to apower socket and set the temperature