Sensor Switch WSX User Manual

1 of 2Sensor Switch 900 Northrop Road, Wallingford, CT 06492 Phone: 1.800.PASSIVE sensorswitch.com ©2014 Acuity Brands Lighting, Inc. All rights reserved 01/26/14
WSX FAMILY
INSTRUCTIONS
PHYSICAL SPECS
SIZE: 2.74”H x 1.68”W x 1.63”D (6.96 cm x 4.27 cm x 4.14 cm)
(not including ground strap)
WEIGHT: 5 oz
MOUNTING: Single Gang Switch Box
MOUNTING HEIGHT: 30-48 in (76.2-121.9 cm)
SILICONE FREE
ROHS COMPLIANT
ELECTRICAL SPECS
MAXIMUM LOAD (Single Phase)
800 W @ 120 VAC
1200 W @ 277 VAC
1500 W @ 347 VAC
MINIMUM LOAD: None
MOTOR LOAD: 1/4 HP
FREQUENCY: 50/60 Hz (timers are 1.2x for 50 Hz)
ENVIRONMENTAL SPECS
OPERATING TEMP
Standard: 14º to 122º F (-10º to 50º C)
LT Option (PIR): -40º to 122º F (-40º to 50º C)
LT Option (PDT): -4º to 122º F (-20º to 50º C)
RELATIVE HUMIDITY:
Standard: 20 to 75% non-condensing
LT Option: 20 to 90% non-condensing
(electronics coated for corrosion resistance)
SPECIFICATIONS
COVERAGE PATTERN
36 30 20 10 0 ft 10 20 30 36
12 9 6 3 0 m 3 6 9 12
Small
motion
detection
Small
motion
detection
to ~20 ft
6
3
0 m
20
10
0 ft
Small motion ~40 ft coverage
TOP VIEW
1.2 m
4 ft
Small motion
detection to ~20 ft
Large motion detection to >36 ft
SIDE VIEW
0 18 27 369
ft
0 6 9 123
m
This product is pre-congured for wiring without a neutral; however, if connection to neutral is required by code, the unit easily converts in seconds.
CONVERSION FROM GROUND ONLY NO NEUTRAL TO NEUTRAL WIRING
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
Step 1:
Remove Yellow
Label
Step 2:
Loosen Screws and
Remove Metal Link
Step 3:
Connect Neutral to
Silver Screw and
Ground to Green Screw
WIRING TO GROUND NO NEUTRAL WIRING TO NEUTRAL
• Small motion (e.g. hand movements) detection up to 20 ft (6.10 m), ~625 ft
2
• Large motion (e.g. walking) detection greater than 36 ft (10.97 m), ~2025 ft
2
• Wall-to-wall PIR coverage
• Units with -PDT (Passive Dual Technology) option
(also called Microphonics) provide overlapping
detection of human activity over the complete
PIR coverage area. Advanced ltering is utilized
to prevent non-occupant noises from keeping
the lights on.
TOP VIEW
BASE MODEL #s
WSX: Passive Infrared (PIR) Detection - Auto On
WSX SA: Passive Infrared (PIR) Detection - Manual On
WSX NL: Passive Infrared (PIR) Detection - Manual On
WSX PDT: Dual Technology (PIR + Microphonics) Detection - Auto On
WSX PDT SA: Dual Technology (PIR + Microphonics) Detection - Manual On
WSX PDT NL: Dual Technology (PIR + Microphonics) Detection - Manual On
36 30 20 10 0 ft
10 20
30 36
12 9 6 3 0 m
3 6 9 12
Small
motion
detection
Small
motion
detection
to ~20 ft
6
3
0 m
20
10
0 ft
Small motion ~40 ft coverage
TOP VIEW
1.2 m
4 ft
Small motion
detection to ~20 ft
Large motion detection to >36 ft
SIDE VIEW
0 18 27 369
ft
0 6 9 123
m
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
GND
H
N
BLK BLK
BLK
BLK
LOAD
GND
120/277 VAC WIRING
BLACK* - Line Input
BLACK* - Load Output
*BLACK wires
can be reversed
}
WIRE COLOR KEY
347 VAC WIRING (-347 Option)
Red wires replace Black wires.
For additional wiring diagrams, scan QR CODE below or go to:
GND
H
N
LOAD
BLK
BLK
REMOVE METAL LINK
IF CONNECTING TO
NEUTRAL
H
N
LOAD
BLK
BLK
N
GND
NOTE: When wiring in parallel, both
units must time out for lights to
turn o. Disabling switch function is
recommended (Function 4, Setting 2).
http://bit.ly/12HaeEF
GND
H
N
BLK BLK
BLK
BLK
LOAD
GND
N
N
PARALLEL 3WAY
PARALLEL 3WAY

Sensor Switch WSX Specifications

General

Brand	Sensor Switch
Model	WSX
Category	Accessories
Language	English

Summary

SPECIFICATIONS

PHYSICAL SPECS

Details physical dimensions, weight, mounting height, and compliance.

ELECTRICAL SPECS

Specifies maximum load ratings for single-phase AC power.

COVERAGE PATTERN

Describes motion detection range and benefits of dual technology.

BASE MODEL #s

Lists different WSX model variations and their core detection features.

CONVERSION FROM GROUND ONLY (NO NEUTRAL) TO NEUTRAL WIRING

WIRING TO GROUND (NO NEUTRAL)

Wiring diagram for connecting the device without a neutral wire.

WIRING TO NEUTRAL

Wiring diagram for connecting the device with a neutral wire.

WIRE COLOR KEY

Explains wire color conventions for 120/277 VAC and 347 VAC wiring.

OPERATIONAL SETTINGS

Occupancy Time Delay

Configures how long lights remain on after the last occupancy detection.

On Mode

Sets automatic or manual lighting control and sensitivity levels.

Switch Modes

Defines button functionality, including override and disable options.

Photocell Set-Point

Sets ambient light threshold to prevent initial light turn-on.

LED Operation

Configures the device's LED indicator behavior for occupancy or relay.

Restore Factory Defaults

Resets all device settings to their original factory configuration.

Minimum On Time

Sets required initial duration for lamps after switching on.

Manual On Grace Period

Time after turn-off for reactivation by motion or manual input.

Dual Technology (Microphonics™)

Adjusts Microphonics sensor responsiveness for PDT models.

Microphone Grace Period

Time after turn-off for voice reactivation with PDT models.

Predictive Mode Exit Time

Time after manual off for occupants to leave before sensor checks.

Predictive Mode Grace Time

Time after exit time for rescanning room for remaining occupants.

PROGRAMMING INSTRUCTIONS