SEVERIN PG 8104 - After Grilling

13
142 x 208 mm
Timer
The timer is used to monitor the grilling time. It can be set
from 1 min to 23 h 59 mins. Beep signals indicate that the
running time has elapsed; the heating element remains
switched on.
∙ Turn the rotary control until lights up.
∙ Presstherotarycontrolbrieyandturntoselectthe
hours.
∙ Presstherotarycontrolbrieyandadjusttheminutes.
∙ Conrmthetimesettingbybrieypressingthecontrol.
Thecolonstartsashing;oncethetimehaselapsed,
beep signals are heard.
∙ To return to stand-by mode, press the rotary control for
two seconds.
∙ Alternatively, set the timer to 0:00, and press the control
brieytoreturntostand-bymode.
∙ If the heating is switched off after the timer is set, the
appliance will change to sleep-mode 5 minutes after the
last input, i.e. the timer is switched off.
∙ If the timer is set with the heating already off, it will
continue until the pre-selected time is reached, when the
unit changes to sleep-mode.
Grilling 80-320 °C
Togrillsausages,poultry,shetc.Fornishingorkeeping
warm steaks.
The entire grill surface is heated.
∙ Turn the rotary control until lights up.
∙ Presstherotarycontrolbrieyandturntoselectthe
desiredtemperature.Pressbrieytoconrm.
∙ Theringstartsashingorangeandtheapplianceis
heating up.
∙ Once the selected temperature has been reached, the
ring shows steady orange.
∙ Place the food on the grill surface.
‘Boost-zone’ grilling 330-500 °C
For searing or light grilling of steaks.
The boost-zone is located to the right; the left side is
heated to 320 °C.
∙ Turn the rotary control until lights up.
∙ Presstherotarycontrolbrieyandturntoselectthe
desiredtemperature.Pressbrieytoconrm.
∙ Theringstartsashingredandtheapplianceisheating
up.
∙ Once the selected temperature has been reached, the
ring shows steady red.
∙ Place the food on the boost-zone.
∙ For subsequent cooking, lower the temperature or shift
the food to the left on the grill surface.
Grilling with the core thermometer
∙ Fit the thermometer plugs into the sockets at the lower
left of the junction box . To prevent the appliance from
switching off, ensure that the box is not lifted up and
stays properly connected.
∙ Select the desired grill function and temperature.
∙ Once pre-heating is complete and the ring shows a
steady light, put on the food.
∙ Push the tips of the thermometers into the centre of the
food.
∙ Usetherotarycontroltosetthedesiredcore
temperature -
or .Pressbrieytoconrm.
∙ The display shows the respective current core
temperature.
∙ Once the pre-set core temperature on one thermometer
is reached, three long beep signals are heard.
∙ Remove the respective thermometer and take off the
food.
∙ Note:
The grill plate remains on even after the pre-set core
temperature has been reached.
Stand-by mode
∙ To switch off the heating and return to stand-by mode,
press the rotary control for two seconds.
∙ Alternatively,pressthecontrolbriey,setthe
temperature to 00andpressagainbrieytoreturnto
stand-by mode.
Sleep mode
∙ If the heating is switched off, the appliance will change
to sleep-mode 5 minutes after the last input.
∙ To switch off earlier, press the rotary control for two
seconds.
After grilling
∙ Always disconnect the unit from the mains and allow it to
cool down after grilling.