SewingMachinesPlus QF00007-12 User Manual

King Quilter Frame Assembly 1
King Quilter Frame
NOVEMBER 2018
Assembly Instructions
Table of Contents
Parts List ..........................................page 2
Preparation: Batting Bar Bracket Assembly, Do this First! ....page 7
Step 1: End Leg Assembly ..............................page 8
Step 2: Table Assembly ...............................page 14
Step 3: Center Leg Assembly ...........................page 15
Step 4: End Leg to Table Assembly ......................page 17
Step 5: Precision-Glide Track Assembly .................. page 22
Step 6: Front Pole Carrier / Rear Pole Carrier Arm Assembly . page 25
Step 7: Bungee Cleat Assembly .........................page 26
Step 8: Leveling the Frame .............................page 27
Step 9: Pole Assembly ................................page 28
Step 10: Adding Pole Ends .............................page 29
Step 11: Pole to Frame Assembly ....................... page 31
Step 12: Rubber End Cap Assembly ......................page 32
Step 13: Bungee Clamp Assembly .......................page 33
Step 14: Hook and Loop Strips on Poles Assembly ..........page 34
Step 15: Attach Leaders ..............................page 35
#QF00007-12 and QF00007-10

SewingMachinesPlus QF00007-12 Specifications

General

Brand	SewingMachinesPlus
Model	QF00007-12
Category	Sewing Machine
Language	English

Summary

Parts List

Frame Component Identification

Lists and illustrates all major frame sections and hardware components.

Preparation: Batting Bar Bracket Assembly

Install Batting Bar Brackets

Attaching batting bar brackets to upright beams before main assembly.

Step 1: End Leg Assembly

Assemble Left Rear Leg

Connecting the left rear leg lower to upper and attaching to beams.

Attach Side and Gusset Brackets

Securing outer side and gusset brackets to the leg assembly.

Assemble Right Rear Leg

Repeating the end leg assembly process for the right side.

Step 2: Table Assembly

Join Table Sections

Connecting the table sections using splice braces.

Secure Table Assembly

Tightening screws to secure the joined table sections.

Step 3: Center Leg to Table Assembly

Install Center Legs

Attaching center leg assemblies to the joined table sections.

Adjust and Tighten Center Legs

Ensuring proper height and securing center legs.

Step 4: End Leg to Table Top Assembly

Attach Left Leg Assembly

Connecting the left leg assembly to the table top with screws.

Secure and Align Left Leg

Tightening screws and ensuring proper alignment for the left leg.

Attach Right Leg Assembly

Connecting the right leg assembly to the table top.

Align and Secure Frame

Adjusting leg assemblies for parallelism and tightening screws.

Final Frame Checks

Verifying flatness and preliminary leveling adjustments.

Step 5: Precision-Glide Track Assembly

Assemble Track Sections

Joining track support sections using couplers and screws.

Install Plastic Tracks

Sliding plastic tracks into assembled aluminum supports.

Attach Tracks to Frame

Securing the track assemblies to the table top.

Align and Mount Carriage

Aligning tracks and placing the machine carriage.

Step 6: Front Pole Carrier & Rear Pole Carrier Arm Assembly

Install Front Pole Carriers

Attaching front pole carriers to the upper beam.

Install Rear Pole Carrier Arms

Attaching rear pole carrier arms to the vertical beam.

Step 7: Bungee Cleat Bar Assembly

Attach Bungee Cleat Bars

Securing bungee cleat bars to carriers and arms.

Ensure Bar Parallelism

Checking and adjusting bungee cleat bar alignment.

Step 8: Leveling the Frame

Adjust Leveling Feet

Using leveling feet to ensure the frame is stable and even.

Step 9: Pole Assembly

Assemble Pole Sections

Joining pole sections together using pole couplers.

Step 10: Adding the Pole Ends

Install Ratchet and Idler Ends

Attaching ratchet and idler end caps to pole assemblies.

Assemble Hand Wheel

Mounting the hand wheel onto a pole assembly.

Step 11: Pole to Frame Assembly

Place Poles onto Frame

Positioning the batting storage, backing, quilt-top, idler, and take-up poles.

Step 12: Rubber End Cap Assembly

Attach Rubber End Caps

Sliding rubber end caps onto bolts of backing and quilt top poles.

Step 13: Bungee Clamp Assembly

Secure Bungee Clamps

Threading and locking bungee cords into clamps.

Step 14: Hook and Loop on Pole Assemblies

Apply Hook and Loop Strips

Adhering hook and loop strips to quilt-top, backing, and take-up poles.

Step 15: Attach Leaders

Mark and Attach Leaders

Marking and attaching leaders to the pole assemblies.