11 12
Menu operation
Programme setup
Auto installation
Analogue setting
Programme edit
Programme setup
Select
Digital setting
1
Press MENU and the MENU screen displays.
2
Press
c
/
d
to select the desired menu.
(Programme setup, Picture, Audio, ECO, Setup,
Option)
3
Press
a
/
b
to select the desired menu item.
Press ENTER to proceed if necessary.
4
Press
a
/
b
or
c
/
d
to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
5
Press RETURN as necessary to return to
the previous MENU. Press MENU to exit the
MENU.
Picture menu
H
Picture adjust
Adjustment items
Selected item
c
button
d
button
Backlight
The screen dims The screen brightens
Contrast
For less contrast For more contrast
Brightness
For less
brightness
For more brightness
Colour
For less colour
intensity
For more colour
intensity
Tint
Skin tones
become reddish
Skin tones become
greenish
Sharpness
For less
sharpness
For more sharpness
NOTE
• “Picture adjust” cannot be changed during “DYNAMIC
(FIXED)” mode.
• For resetting all “Picture adjust” items to factory preset
values, press
a
/
b
to select “Reset”, press ENTER, press
a
/
b
to select “Yes”, and then press ENTER.
H
DNR (Digital Noise Reduction)
Reduces noise on screen and produces a clearer
video image. (Auto, High, Low, Off)
H
Wide mode
You can manually select the size of a picture
appeared on your screen.
Selectable picture size varies with the type of signal
received.
Press
a
/
b
while the wide mode menu displays on
the screen.
• As you toggle down the options, each mode is immediately
refl ected on the TV.
Selected item Description
Normal
Keeps the original aspect ratio in a full
screen display.
Zoom 14:9
For 14:9 letterbox pictures. A thin side
bar appears on each side, and you may
also see bars on the top and bottom
with some programmes.
Panorama
In this mode the picture is progressively
stretched toward each side of the
screen.
Full
For 16:9 squeeze pictures.
Cinema 16:9
For 16:9 letterbox pictures. Bars may
appear on the top and bottom with
some programmes.
Cinema 14:9
For 14:9 letterbox pictures. Bars may
appear on the top and bottom with some
programmes.
Dot by Dot
Displays an image with the same number
of pixels on the screen.
Underscan
Display with an Underscan image only
when receiving a 720p signal.
Display
with the High-Defi nition image adjusted
optimally. Noise may appear on the edge
of the screen with some programmes.
Just scan
Keeps the original aspect ratio and
enlarges the picture as much as possible.
Auto
Keeps the original aspect ratio based on
source information and enlarge the picture
as much as possible.
NOTE
• Some picture sizes may not be displayable depending on
the input signal.
• “Auto” and “Just scan” can be selected only during video
playback in “Movie mode” of USB Media Player.
Programme setup (Continued)
Programme edit
Use this menu to set up a channel individually.
1
Repeat steps 1 to 2 in Auto search.
2
Press
a
/
b
to select “Programme edit”, and
then press ENTER.
3
Press
a
/
b
to select the channel you want
to edit, and then press 1 to 5 on the remote
control if necessary or press RETURN to exit.
• As you toggle down the channels, each channel is
immediately refl ected in the background when you
press ENTER.
1
(
Erase programme)
Channels can be erased individually.
Press 1 to erase the selected channel.
2
(Label)
You can change channel names individually.
Maximum 5 alphanumerics can be input.
Press 2 to start labelling.
Press
a
/
b
/
c
/
d
to select a character, and
then press
2
again or ENTER to save.
3
(Sort)
Channel positions can be sorted freely.
Press 3 to select the channel you want to move.
Press
a
/
b
to move it to the desired position,
and then press
3 again or ENTER
to save.
4
(
Skip)
Channels with “Skip” set to “On” are passed
over when using CH
r
/
s
even if selected
while watching the image from the TV.
Press 4 to skip the selected channel.
Press 4 again to cancel the skip.
5
(Lock)
You can block the viewing of any selected
channel.
Password must be set fi rst to allow “ ” to
function.
• See page 13 for setting a password.
Press 5 to lock the selected channel.
Press 5 again to unlock the locked channel.
Selecting a preset AV mode
“AV mode” gives you several viewing options to
choose from to best match the system environment,
which can vary due to factors like room-brightness,
type of programme watched or the type of image
input from external equipment.
1
Press MENU and the MENU screen displays.
2
Press
c
/
d
to select “Picture” and “Audio”.
3
Press
a
/
b
to select “AV mode”, and then
press ENTER.
Selected item Description
STANDARD
For a highly defi ned image in a
normally bright room.
MOVIE
For a movie.
PC
For PC (Available only when inputting
an HDMI).
DYNAMIC
For a clear-cut image emphasising
high contrast for sports viewing.
DYNAMIC
(FIXED)
Changes the image and sound
settings to the factory preset values.
No adjustments are allowed.
COMFORT
MODE
Reduce the blue light of the TV.
SUPER ECO
Reduce backlight brightness to save
power consumption.
NOTE
• You can select a different AV mode item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for VIDEO input.)
2T-C50AD1X_H025_EN.indd 62T-C50AD1X_H025_EN.indd 6 4/20/2018 4:12:09 PM4/20/2018 4:12:09 PM
To Next Page
Loading...
