Sharp CD-PC651H

(Continued)
_
7
(Main unit operation) |
Notes:
® When there are no station names siored in memory,
you cannot use this function. In this case, when the
STATION button is pressed, "NOTHING" will flash
for 5 seconds, and the unit will return to the original
display.
@ This function can only be used when the FM band
has been selected.
@ The same station name can be stored in different
preset channels. Therefore, when you are choosing
a station name from the presets, the same siation
name may be encountered more than once.
@ In a certain area or during certain time periods, the
station names selected using the station select func-
tion may temporarily be different from the name of
the station you are actually receiving.
Mi
To
specify
station
names
and
select
stations
manually
(station
select)
You
can
receive
a
desired
station
by
specifying
the
station
name
(BBC
R1,
BBC
R2,
etc.)
from
among
the
stations
that
have
been
stored
in
memory.
{(ASPM
is
convenient
for
storing
stations
in
memory.)
Before
starting
this
operation,
you
must
store
one
or
more
station
names
in
memory.
1
Press
the
ON/STAND-BY
button
to
turn
the
power
on.
2
Press
the
TUNER
(BAND)
button.
3
Press
the
TUNER
(BAND)
button
to
select
the
FM
ST
or
EM
band.
4 Press the STATION button.
@
"STATION"
and
"SELECT"
will
appear
alternately
for
about
6
seconds.
5
Within
6
seconds,
press
the
PRESET
(vv
or
A)
button
to
select
a
desired
station
name
you
want.
@
Each
time
the
button
is
pressed,
the
station
name
will
appear.
If
the
button
is
held
down
for
more
than
0.5
seconds,
the
Station
name
will
continuously
change.
6
Whilst
the
selected
station
name
is
flashing
(within
6
seconds},
press
the
STATION
button
again.
@
After
the
selected
station
name
has
been
lit
for
4
second,
the
preset
station
which
corresponds
io
the
selected
station
name
will
be
recalled.
To cancel the station select operation:
Press
the
STATION
button
whilst
"STATION"
and
"SELECT"
ap-
pear aiternaiely.
To
try
to
store
a
station
name
again,
if
the
wrong
name
was
stored
in
memory
by
mistake:
When
you
store
station
names
in
memory
using
the
ASPM
func-
tion,
the
correct
station
names
may
not
actually
be
stored
if
there
is
lots
of
noise
or
if
the
RDS
station
signal
is
too
weak.
In
this
case,
try
storing
station
names
in
memory
using
the
fol-
lowing
procedure.
1 Press the STATION button.
2
Within
6
seconds,
press
the
PRESET
(
or
AN)
button
to
check
whether
the
station
names
are
correct.
3
If
you
find
a
station
name
that
is
wrong,
press
the
STATION
button
again
within
6
seconds
to
recall
the
preset
station,
which
corresponds
to
the
station
name.
4
Afier
the
preset
station
has
been
received
and
the
correct
station
name
has
been
displayed,
press
the
MEMORY/SET
button.
5
within
30
seconds,
Press
the
MEMORY/SET
button
whilst
the
preset
channel
number
is
flashing.
@
The
new
station
name
has
been
stored
in
memory
correctly.
E-21