Why won't my Sharp ES-HA612WD-BE start?
If your Sharp Washer doesn't start, several factors could be at play. Ensure the machine is properly plugged in and that the fuses are in good working order; replace them if necessary. Verify that there is a stable mains power supply. Don't forget to press the Start/Pause button and confirm that the program dial is set to your desired position. Finally, make sure the machine door is fully closed.
What to do if my Sharp ES-HA612WD-BE does not discharge water?
If your Sharp Washer isn't draining water, the drain hose might be clogged or twisted; inspect it, and either clean or untwist it. Another potential issue is a clogged pump filter, which should be cleaned. Also, if the laundry is too tightly packed in the drum, redistribute it evenly.
Why is the spin cycle delayed on my Sharp Washer?
If the spin cycle on your Sharp Washer is delayed or doesn't occur, it might be because the Unbalanced load control system has been activated. This is not a fault. The system is attempting to redistribute your laundry. Once the load is balanced, the spin cycle will commence. For future washes, load the drum evenly.
How to stop my Sharp Washer from vibrating?
If your Sharp Washer vibrates excessively, it might be due to several reasons. Check if the feet of the machine have been properly adjusted. Ensure that the transit bolts, used for transportation, have been removed. Avoid placing the machine on a hard surface. If you've overloaded the machine or the laundry is unevenly spread, redistribute the load evenly. Note that a small load can also cause vibration, but this will not prevent the operation of your machine.
Why is my Sharp Washer not taking in water?
If your Sharp Washer isn't taking in water, start by checking if the water tap is turned on. Inspect the water inlet hose for any twists and untwist if necessary. Also, the water inlet hose or inlet filter may be clogged, so clean these filters. Lastly, ensure that the machine door is completely closed.
Why is my Sharp ES-HA612WD-BE Washer not cleaning clothes properly?
If you're not satisfied with the washing results from your Sharp Washer, consider whether your laundry is too dirty for the selected program. Refer to the program tables to choose a more suitable program. Also, ensure you're using enough detergent as instructed on the packaging, and that you're not overloading the machine beyond the maximum capacity for the selected program.
What to do if my Sharp ES-HA612WD-BE is not cleaning well in hard water?
If you're experiencing unsatisfactory washing results with your Sharp Washer, especially in areas with hard water, try increasing the amount of detergent according to the manufacturer’s instructions. Also, make sure your laundry is spread out in the drum.
How to reduce foam in my Sharp ES-HA612WD-BE detergent drawer?
If you notice excessive foam in the detergent drawer of your Sharp Washer, it's likely due to using too much detergent or using the wrong type. To stop the foam, press the Start/Pause button, then dilute one tablespoon of softener into 1/2 litre of water and pour into the detergent drawer. Press the Start/Pause button again after 5-10 minutes. Ensure you only use detergents specifically produced for automatic Washing Machines.
Why does my Sharp ES-HA612WD-BE discharge water immediately after loading?
If your Sharp Washer immediately discharges water as soon as it's loaded, the end of the water drain hose might be positioned too low. Check that the drain hose is at a suitable height.
How to remove detergent residue from laundry after using my Sharp Washer?
If your laundry has detergent residue after washing in your Sharp Washer, it may be due to non-dissolving particles in some detergents appearing as white spots. You can perform an extra rinse or clean your laundry with a brush after it dries.
General| Washing Capacity | 6 kg |
|---|---|
| Spin Speed | 1200 rpm |
| Energy Efficiency Class | A+++ |
| Noise Level (Washing) | 58 dB |
| Color | White |
| Water Consumption | 45 L |
To Next Page