This document is a user manual for the SHARP ES-HFA6103WD-EE Washing Machine, a front-loading appliance designed for domestic use.
Function Description
The SHARP ES-HFA6103WD-EE is a washing machine designed to clean various types of laundry using a range of programs and additional functions. It features a detergent drawer with compartments for liquid/powder detergent, softener, and pre-wash detergent. The machine is equipped with a control panel including a program dial and an electronic display to manage washing cycles. It also incorporates a half-load detection system to optimize water and energy consumption for smaller loads.
Important Technical Specifications
- Operating Voltage / Frequency: 220-240 V~/50Hz
- Total Current: 10 A
- Water Pressure: Maximum 1 Mpa / Minimum 0.1 Mpa
- Total Power: 2100 W
- Maximum Washing Capacity (dry laundry): 6.0 kg
- Spinning Revolution: 1000 rev/min
- Number of Programmes: 15
- Dimensions (mm):
- Height: 845
- Width: 597
- Depth: 497
The machine requires a 220-240V, 50Hz mains supply and should be connected to an earthed 10-amp socket. Water inlet connections can be single (cold) or double (hot and cold), with hot water supply not exceeding 70°C. The water drain hose must be installed at a maximum height of 100 cm from the ground.
Usage Features
The washing machine offers a variety of programs tailored for different fabric types and soil levels, including:
- Cotton 90°C: For very dirty cotton and flax textiles.
- Cotton Pre-Wash 60°C: For dirty cotton and flax textiles with a pre-wash cycle.
- Cotton 60°C: For dirty cotton and flax textiles.
- Eco 40-60: For normally soiled cotton laundry washable at 40°C or 60°C.
- Cotton 20°C: For less dirty cotton and linen textiles.
- Easy Care 40°C: For very dirty or synthetic-mixed textiles.
- Wool 30°C: For woollen laundries with machine wash labels.
- Rinsing: Provides an additional rinse.
- Spinning: Provides an additional spin cycle.
- Hand Wash/Delicate 30°C: For hand wash or sensitive laundry.
- Colors 40°C: For less dirty cotton and linen textiles.
- Mixed 30°C: For dirty cotton, synthetics, colour, and flax textiles.
- Blouses / Shirts 60°C: For dirty cotton, synthetic, and synthetic-mixed shirts and blouses.
- Fast 60 min. 60°C: For dirty cotton, coloured, and linen textiles washed at 60°C in 60 minutes.
- Rapid 15 min. 30°C: For lightly soiled cotton, colored, and linen textiles.
Additional functions can be selected before starting a program:
- Delay Timer: Allows delaying the start of a program by 3, 6, 9, or 12 hours.
- Spin Speed Selection: Adjusts the spin speed, with a "No Spin" option available.
- Anti-Allergic: Adds an extra rinse operation with hot water, recommended for delicate skin, baby clothes, and underwear.
- Easy Ironing: Reduces wrinkling at the end of the wash program.
- Pre-Wash: For heavily soiled laundry, requiring detergent in the pre-wash compartment.
- Extra Rinse: Adds an additional rinse at the end of the program.
- Cold Wash: Sets the selected program to use cold water.
- Rapid Wash: Reduces wash time, energy, and water consumption, recommended for loads less than half the maximum capacity.
The machine features a child lock function to prevent unintentional operation. Programmes can be cancelled at any time by turning the program dial to "STOP," which will stop the washing operation and drain the machine.
Maintenance Features
Regular maintenance is crucial for the longevity and optimal performance of the washing machine.
- General Cleaning: The machine should be unplugged and the water supply turned off before any cleaning or maintenance. Solvents, abrasive cleaners, glass cleaners, or all-purpose cleaning agents should not be used on the machine.
- Water Inlet Filters: These filters prevent dirt from entering the machine and should be cleaned every 2 months, or if the machine is not receiving sufficient water. This involves unscrewing the inlet hoses, pulling out the filters with pliers, cleaning them with a soft brush and soapy water, and then re-inserting them.
- Pump Filter: The pump filter system prolongs the life of the pump by preventing lint from entering. It is located behind a cover on the front-lower right corner and should be cleaned every 2 months. The process involves opening the cover, draining any residual water into a container, loosening and removing the filter by turning it anticlockwise, cleaning it with a soft brush, and then re-fitting it.
- Detergent Drawer: Detergent residue can build up over time. The drawer should be removed and cleaned with water and a soft brush every 2 months. Care should be taken to prevent residue from falling into the machine. The detergent drawer should not be washed in a dishwasher.
- Flush Stopper: The flush stopper in the detergent drawer should be disassembled and cleaned to remove softener residue, then re-fitted properly.
- Body: The external casing can be cleaned with a mild, non-abrasive cleaning agent or soap and water, then wiped dry with a soft cloth.
- Drum: Metallic objects should not be left in the drum to prevent rust stains. Non-chlorine cleaning agents should be used for rust stains, avoiding wire wool or similar hard objects.
The manual also provides troubleshooting steps for common issues, such as the machine not starting, not taking in water, not discharging water, vibrating, or excessive foam. It also lists automatic fault warnings (E01, E02, E03, E04) indicated by flashing LEDs, along with their possible causes and recommended actions.
Need help?
To Next Page
General