WASH
Instruction on control panel functions
RINSE
SPIN
NORMAL
JEANS
SPEEDY
DELICATE
BLANKET
TUB CLEAN
Wash heavy and very dirty clothing.
Wash speedy for Not-so-dirty clothing.
POWER
Course for cleaning washing / spin drying tub.
Select the washing time: 2 hrs, 6 hrs, 9 hrs.
Course for reducing the time to dry.
AIR DRY
Spin-drying with high-speed takes air into the inner tub from
the hole of top lid.
AIR DRY course reduce the time to dry in the shade greatly.
Select the time:
[ - ](= 0 min)
, 30 min, 60 min, 90 min.
Control panel / Display
Caution
START/PAUSE
Press this key after turning on, selected course is started.
Plug the machine in and then press this key, the machine
turns on. Press this key again, it turns off.
1.If the machine is energized but not started, the power supply turns
off automatically 5 min later.
2.If no key pressed after the START/PAUSE key is pressed during the
running, the power supply turns off automatically 10 min later.
Press this key again, the running is paused. Press it once again,
the running restarts.
Wash clothing with the HAND WASH mark.
Wash daily clothing like relatively-dirty shirts or pants.
Wash strong for blankets or heavy clothing.
Select WASH as necessary. Select the washing time: [ - ](= 0 min) ,
1 min – 15 min.
Select RINSE as necessary. Select the rinsing time: [ - ](= 0 min) ,
1 time – 3 times.
Select SPIN as necessary. Select the spinning time: [ - ](= 0 min) ,
1 min – 9 min.
Select the appropriate water level depending on course or kinds
of clothing. (Select from 8 steps regulation)
WATER LEVEL
BABYCARE
Wash gently and rinse thoroughly for baby clothing.
15
6
Common non-fault phenomenon (Please refer to
this section if you think an abnormality happens.)
Abnormal display
Present-
-ation
U9
E4
E3
E2
E1
C2
Washing machine
inclines or is shaky.
The clothing is
lopsided.
The end of drain
hose is blocked.
The drain position is
relatively high.
Top cover is not clo-
-sed during spin
drying.
Possible non-fault
cause
Coping process
Failure
cause
Low flow at the
faucet.
Water inlet filter net
is blocked.
It generates a beep when washing machine indicates abnormal display. If not connec-
ted in 10 min, it turns off automatically.
Because the phenomenon may not be a fault, please check it again before sending
the machine for repair. In the case of failure, please consult the maintenance depart-
-ment. Be sure not to disassemble and repair the machine without permission.
Caution
List of failure cause
Water level sensor
shows an abnormal
level.
Failure of water inlet
valve
Connector contact
failure
Wiring disconnection
Failure of safety switch
Failure of drain valve
Failure of drain valve
motor
Circuit failure
Get water in tube of
water level sensor
Connect failure on
drain valve motor
The faucet is closed.
Top cover is opened
as the reservation
course starts.
Drain hose is folded/
crumpled/tied.
Inclease water supply,
press START / PAUSE
key.
Turn the faucet on,
press START/PAUSE
key.
Failure of water level
sensor
Clean filter net, press
START/PAUSE key.
Close top cover.
Adjust drain hose pro-
-perly, press START
/PAUSE key.
Clean drain hose,
press START/PAUSE
key.
Washing machine place
the horizontally with
adjusting the foots.
Distribute the clothing
evenly.
Pull out the plug from
the plug seat, and ent-
-rust the maintenance
department.
Top cover opened
in the situation of
CHILD LOCK.
Turn the power off, and
take it from the top.
CHILDLOCK is not re-
-leased, unless you re-
set it manually.
Caution
ECO
Water is saved by 1 time static rinse.
To Next Page
Loading...
Need help?
General
