MX3500N SIMULATION 7 – 45
30-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors of the paper feed sec-
tion and the related circuits.
Section
Paper feed
Item
Operation
Operation/Procedure
1) When the machine enters Simulation 30-02, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor
name is highlighted.
<Sensor name>
33
33-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the card
reader sensor and the related circuits. (The
card reader sensor operation can be moni-
tored with the LCD display.) (Japan only)
Section
Other
Item
Operation
Operation/Procedure
1) When the machine enters Simulation 33-01, the following
screen is displayed to show the sensor status change.
* When each sensor is turned ON, the corresponding sensor name
is highlighted.
<Sensor name>
40
40-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the detection level of the
manual feed tray paper width detector.
Section
Paper feed
Item
Operation
Operation/Procedure
1) Extend the manual feed tray guide to the max. width and press
[EXECUTE] button. [EXECUTE] button is highlighted and the
current AD value is temporality saved to RAM as the max.
width.
* During adjustment, "EXECUTING..." is displayed.
* After completion of the max. width adjustment, the P1 width
(A4) adjustment value start screen is displayed.
2) Extend the manual feed tray guide to the P1 (A4) width posi-
tion and press [EXECUTE] button. [EXECUTE] button is high-
lighted and the current AD value is temporality saved to RAM
as the P1 width (A4) position. (Hereinafter, the value is saved
for each size setting.)
3) Perform the adjustment of P2 position width (A4R) and min.
position according to the above procedures.
4) After completion of the adjustment, "COMPLETE" is displayed
and the RAM contents are saved to EEPROM. If the adjust-
ment is not completed normally for any reason, "ERROR" is
displayed and data are not saved to EEPROM. In this case,
the adjustment must be tried again.
DSW_F Front cover open/close detection
DHPD_K K phase detection
DHPD_CL CL phase detection
1TNFD Waste toner full detection
1TUD_CL Primary transfer belt separation CL detection
1TUD_K Primary belt separation BK detection
Sensor name (Display) Content
CPFD1 Cassette 1 transport detection
CLUD1 Cassette 1 upper limit detection
CPED1 Cassette 1 paper empty detection
CSPD1 Cassette 1 paper remaining quantity detection
CSS11 Cassette 1rear edge detection 1
CSS12 Cassette 1 rear edge detection 2
CSS13 Cassette 1 rear edge detection 3
CSS14 Cassette 1 rear edge detection 4
CPFD2 Cassette 2 transport detection
CLUD2 Cassette 2 upper limit detection
CPED2 Cassette 2 paper empty detection
CSPD2 Cassette 2 paper remaining quantity detection
CSS21 Cassette 2 rear edge detection 1
CSS22 Cassette 2 rear edge detection 2
CSS23 Cassette 2 rear edge detection 3
CSS24 Cassette 2 rear edge detection 4
MPFD Manual feed paper entry detection
MPLD Manual feed paper length detection
MTOP1 Manual feed tray reduction detection
MTOP2 Manual feed tray extension detection
MPED Manual feed paper empty detection
Code of sensor Sensor name
0
MAIN UNIT SENSOR CHECK
CLOSE
SIMULATION NO.30-01
TEST
1/1
PPD1 PPD2 POD1 POD2
POD3 TFD2 TFD3 HPOS
DSW_R DSW_C DSW_F DHPD_K
DHPD_CL 1TNFD 1TUD_CL 1TUD_K
0
TRAY SENSOR CHECK(MAIN)
CLOSE
SIMULA TION NO.30㧙02
TEST
1/2
MPFD MPLD
MTOP1
MTOP2
CPFD1 CLUD1
CPED1
CSPD1
CSS11 CSS12
CSS13
CSS14
CPFD2
CLUD2 CPED2 CSPD2
CSS21
CSS22 CSS23 CSS24
Code (Display) Sensor name
CARD Card insertion detection
DATA Card number signal detection
CLOCK Standard clock signal detection
To Next Page
Loading...
