Sharp PN-80TC3 - Page 44

PN-L803C/80TC3 INSTALLATION, ADJUSTMENT, SETTING, OPERATION 2 - 22
ITEM DETAIL 1 DETAIL 2 ADJUSTMENT
Input terminal
DisplayPort
HDMI1［AV］
HDMI1[PC]
HDMI2［AV］
HDMI2[PC]
HDMI3［AV］
HDMI3[PC]
D-SUB1［RGB］
D-SUB1［VIDEO］
D-SUB1［COMPONENT］
D-SUB2［RGB］
SIDE USB ● ● ● ● ● ● ● ● ● ● ●
SIDE INPUT TERM. ● ● ● ● ● ● ● ● ● ● ●
DisplayPort ● ● ● ● ● ● ● ● ● ● ●
HDMI1 ● ● ● ● ● ● ● ● ● ● ●
HDMI2 ● ● ● ● ● ● ● ● ● ● ●
HDMI3 ● ● ● ● ● ● ● ● ● ● ●
D-SUB1 ● ● ● ● ● ● ● ● ● ● ●
D-SUB2 ● ● ● ● ● ● ● ● ● ● ●
- ● ● ● ● ● ● ● ● ● ● ●
COMMUNICATION SETTING) ● ● ● ● ● ● ● ● ● ● ●
RS-232C/LAN SELECT) ● ● ● ● ● ● ● ● ● ● ●
S-232C ● ● ● ● ● ● ● ● ● ● ●
LAN ● ● ● ● ● ● ● ● ● ● ●
BAUD RATE) ● ● ● ● ● ● ● ● ● ● ●
Value 9600, 19200, 38400 bps ● ● ● ● ● ● ● ● ● ● ●
LAN SETUP ● ● ● ● ● ● ● ● ● ● ●
DHCP CLIENT ● ● ● ● ● ● ● ● ● ● ●
OFF ● ● ● ● ● ● ● ● ● ● ●
ON ● ● ● ● ● ● ● ● ● ● ●
IP ADDRESS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Value Address input ● ● ● ● ● ● ● ● ● ● ●
SUBNET MASK ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Value Address input ● ● ● ● ● ● ● ● ● ● ●
DEFAULT GATEWAY ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Value Address input ● ● ● ● ● ● ● ● ● ● ●
RESET ● ● ● ● ● ● ● ● ● ● ●
Resets to the factory preset values. ● ● ● ● ● ● ● ● ● ● ●
OFF ● ● ● ● ● ● ● ● ● ● ●
ON ● ● ● ● ● ● ● ● ● ● ●
SET ● ● ● ● ● ● ● ● ● ● ●
CANCEL ● ● ● ● ● ● ● ● ● ● ●
MONITOR ● ● ● ● ● ● ● ● ● ● ●
MONITOR ● ● ● ● ● ● ● ● ● ● ●
LANDSCAPE ● ● ● ● ● ● ● ● ● ● ●
PORTRAIT ● ● ● ● ● ● ● ● ● ● ●
OSD H-POSITION ● ● ● ● ● ● ● ● ● ● ●
Value ● ● ● ● ● ● ● ● ● ● ●
OSD V-POSITION ● ● ● ● ● ● ● ● ● ● ●
Value ● ● ● ● ● ● ● ● ● ● ●
OPERATION MODE ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
MODE1 ● ● ● ● ● ● ● ● ● ● ●
MODE2 ● ● ● ● ● ● ● ● ● ● ●
STANDBY MODE ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
STANDARD ● ● ● ● ● ● ● ● ● ● ●
LOW POWER ● ● ● ● ● ● ● ● ● ● ●
OFF IF NO OPERATION ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
OFF ● ● ● ● ● ● ● ● ● ● ●
ON ● ● ● ● ● ● ● ● ● ● ●