Sharp YO-250M - Page 10

ZQ-2500SP
If the amount of memory available on the receiver at the time of
transfer is insufficient, data transfer is not possible. The message
“SPEICHER VOLL" appears. Delete any unnecessary data, verify
whether the available memory is sufficient, and repeat the data
transfer procedure. :
{f an error message appears while transferring data, press
to clear the error.
Notes:
if the mode of the transmitter and the mode of the receiver are not
the same, data transfer is not established. The message “ER-
RORE DATI" is displayed. When transferring TEL data, directories
on the transmitter and receiver can be different. The contents
received by the receiver will be stored in the open directory. For
example, if TEL 1 is selected on the transmitter and TEL 3 on the
receiver before the data transfer is established, the contents of
TEL 1 will be sent to and stored in TEL 3.
® Turn off the SECRET function on both the transmitter and the
receiver before mode transfer.
Transferring backup data
All the contents of the Organizer are transferred. During backup data
transfer, data stored on the receiver is deleted. Proceed with caution.
(Backup data transfer is only possible between identical models.)
1.
To
select
the
data
transfer
function
on
the
receiver
and
set
it
in
the
©
{f
the
amount
of
memory
available
on
the
receiver
at
the
time
of
receive
mode
for
backup
data
transfer,
press
|
MENU
2
transfer
is
insufficient,
data
transfer
is
not
possible.
The
message
2. "“SPAZIO MEM. OCCUPATO" appears. Delete any unnecessary
<ORG. © ORG> data, verify whether the available memory is sufficient, and repeat
the data transfer procedure.
If an error message appears while transferring data, press
to clear the error.
Transferring backup data
All the contents of the Organizer are transferred. During backup data
transfer, data stored on the receiver is deleted. Proceed with caution.
(Backup data transfer is only possible between identical models.)
It
is
possible
to
verify
data
by
mode
or
by
mode
or
entry.
If
any
1.
To
select
the
data
transfer
function
on
the
receiver
and
set
it
in
the
discrepancies are found, the message “VERGLEICHSFEHLER" is receive mode for backup data transfer, press | MENU 2
displayed. 2.
SICHERUNGSKOPIEN
EMPFANGSMODUS .
2. To select the data transfer function on the transmitter and perform
backup data transfer, press [MENU] [v] 2 VY:
Verifying data
<ORG. © ORG.>
Verify
data
in
the
SCHEDULE
mode.
BACKUP
1. Select the mode on the transmitter and the receiver.
© Press [TERMIN| then [C-CE]. (Transmitter)
© Press | TERMIN]. (Receiver)
2. Set the receiver in the verify mode.
Press |MENU], then 2 to set the receiver in the verify mode.
MODO RICEZIONE
2. To select the data transfer function on the transmitter and perform
backup data transfer, press [MENU] [v] 2 1Y.
Verifying data
It is possible to verify data by mode or by mode or entry. If any
discrepancies are found, the message "ERRORE DI VERIFICA" is
displayed.
<ORG. + ORG.>
-VERGLEICHT—
Verify data in the SCHEDULE mode.
3. Press [MENU], then 2 to select the data transfer function on 1. Select the mode on the transmitter and the receiver.
MST eneniiee: © Press | AGENDA| then [C-CE]. (Transmitter)
© Press [AGENDA|. (Receiver)
2. Set the receiver in the verify mode.
Press {MENU}, then 2 to set the receiver in the verity mode.
4. Press 1 to perform verification.
<For Italian version>
1. Select the mode on the transmitter and receiver.
* Press [C-CE]. (Transmitter)
® Press | AGENDA |}. (Receiver)
2. Press |MENU], then 2 ("OPZIONE"), the data transfer func-
tion on the receiver.
3. Press 2 (*RICEVERE") to set the unit in the receive mode. 3
<ORG. © ORG.>
-VERIFICA—
. Press [MENU], then 2 to select the data transfer fun ction on
the transmitter.
<ORG. «+ ORG.> cals
4. Press 1 to perform verification.
MODO RICEZIONE
4. Press |MENU}], then 2 ("OPZIONE"), the data transfer func-
tion on the transmitter.
Note: To transfer a single entry display the desired entry and
press [MENU 2.
5. Select 1 ("TRASMETTERE’) to transfer data.
1
-10-