What to do if the Shimano DendoUmaru 4000 Plays display is black?
If the display of your Shimano Fishing Equipment is black or shows all characters, this can happen when the unit is left in a hot environment, like a car boot. The display should return to normal once the temperature decreases.
Why does my Shimano DendoUmaru 4000 Plays Fishing Equipment motor stop while winding?
The motor of your Shimano Fishing Equipment might stop while winding if the boat’s power supply terminal or the reel’s power cord connector is rusty. Ensure all screws on the power cord connector are secure. Remove any rust and try again. Also, check the battery charge.
What to do if Shimano DendoUmaru 4000 Plays Fishing Equipment display is not working?
If nothing appears on the display of your Shimano Fishing Equipment, check if the positive (+) and negative (--) power cord connections are properly connected to the battery. Also, verify the battery has sufficient charge and inspect the surface of the alligator clips for any foreign objects.
Why is my Shimano DendoUmaru 4000 Plays motor not working but the display is?
If the display of your Shimano Fishing Equipment is working but the motor isn't, it could be due to insufficient battery charge, which may cause the motor to work at low speed but not at high speed. A new battery may be required. Also, the motor may not work if the reel's temperature is below 0°C, or if the display shows less than 1m for safety reasons. Charge the battery and test the reel.
Why is my Shimano Fishing Equipment Gunwale Stop position wrong?
The Gunwale Stop position on your Shimano Fishing Equipment might be wrong due to winding tension or stretched line. Perform a 0 set. Note that the Gunwale set is only possible between 1~6m, and settings between 0~1m are rounded up to 1m for safety reasons.
Why does Shimano DendoUmaru 4000 Plays make a strange sound?
If your Shimano Fishing Equipment makes a strange sound even when not winding, the condenser may be vibrating due to an unstable power supply. This should not affect the reel's function, so it is safe to continue using it.
What to do if Shimano DendoUmaru 4000 Plays display not working in cold?
If nothing appears on the display of your Shimano Fishing Equipment when used in extreme cold (below -15°C), the LCD display is likely too cold. Wait for the circuit board inside the unit to warm up. When fishing in extremely cold conditions, it is recommended to keep the reel in the cabin or under cover until needed.
Warnings on voltage, battery, and circuit protection, including high temperature and circuit breaker issues.
Warnings on finger entrapment, water intrusion, and electrical signal interference with medical devices.
Instructions for smoke, fire, motor stoppage, and water damage.
Safety rules for maintenance, power disconnection, and avoiding reel modifications.
Precautions for wet terminals, electric shock risk, and drying appliances.
Warnings about motor issues due to damaged displays and incorrect voltage sources.
Specifies voltage, battery types, and warns against chargers.
Step-by-step guide for connecting the power cord to the reel and battery.
Selecting the appropriate learning method based on line type.
Instructions to access Learning Mode from Standard Mode.
Visual guide for the learning process with PE line without backing.
Visual guide for the learning process when using backing line.
Preparation for PE line learning, including entering the mode.
Using the Technical Lever to wind line with specific tension.
Finalizing learning, removing excess line, and exiting the mode.
Preparation for Nylon line learning, including entering the mode.
Using the Technical Lever to wind line with specific tension.
Finalizing learning, joining lines, and exiting the mode.
Entering the learning mode specifically for backing line.
Winding the backing line using marks as an estimate.
Tying the main line to the backing line and winding 10m.
Winding the rest of the main line and exiting learning mode.
Completing the learning process and winding removed line.
Resets the counter to zero at the surface for accurate depth positioning.
Steps to lower the rig and press 0 Set to complete zero setting.
Function to return the rig to the same depth after line repair.
Stops retrieval for easy rod raising and direct rig movement.
Saves target depth automatically if rig stops for 6+ seconds.
Addresses black screen, no characters, and cold weather issues.
Fixes for setting line learning or discrepancies.
Diagnosing problems when the display works but the motor doesn't.
Checks for winding interruptions and rusty connectors.
General| Brand | Shimano |
|---|---|
| Model | DendoUmaru 4000 Plays |
| Category | Fishing Equipment |
| Language | English |
To Next Page