Shimano ST-R600 User Manual

Technical Service Instructions SI-6C80D
ST-6510
ST-5500-CA
ST-5510
ST-R600
Shimano
Total Integration
General Safety Information
WARNING
• Obtain, read and carefully service instructions when installing
parts. A loose, worn, or damaged parts may cause injury to
the rider.
We strongly recommend that only genuine Shimano
replacement parts be used.
• Read these Technical Service Instructions carefully, and keep
them in a safe place for later reference.
Note
• Operation of the levers related to gear shifting should be made
only when the front chainwheel is turning.
• For smooth operation, always be sure to use the specified
outer casing and the bottom bracket cable guide.
• Grease the inner cable and the inside of the outer casing
before use to ensure that they slide properly.
• Because the high cable resistance of a frame with internal
cable routing would impair the SIS function, this type of frame
should not be used.
• The end of the outer casing which has the aluminum
cap should be at the derailleur side.
Derailleur side
4-mm cap
Plastic cap or 4-mm capAluminum cap
• The cycle computers shown in the table below are compatible.
• Read the service instructions for the cycle computer also.
• Parts are not guaranteed against natural wear or deterioration
resulting from normal use.
• For maximum performance we highly recommend Shimano
lubricants and maintenance products.
• For any questions regarding methods of installation,
adjustment, maintenance or operation, please contact a
professional bicycle dealer.
SM-6500
*1
/ SM-6500-RS / SM-6501
SC-6500 / SC-6501 / SC-M500
Meter unit
Bracket sensor unit
*1
The bracket cover must be replaced.
()
ST-6510 ---> Replace with bracket cover for ST-6501.
ST-5500-CA ---> Replace with ST-5500-C.
27
FD-6503
FC-6503
RD-6500-GS
Series
Shifting lever
Outer casing
Gears
Front derailleur
Front chainwheel
Bottom bracket
Rear derailleur
Freehub
Cassette sprocket
Chain
ULTEGRA
ST-6510 / ST-R600
18
SP40
FH-6500
CS-6500
CN-HG93 / CN-7701
FD-6500
FC-6500
BB-6500
RD-6500
Bottom bracket cable guide
SM-SP17
In order to realize the best performance, we recommend that
the following combination be used.
27
FD-5503 / FD-5504
FC-5504 / FC-5505
RD-5500-GS /
RD-5501-GS
Series
Shifting lever
Outer casing
Gears
Front derailleur
Front chainwheel
Bottom bracket
Rear derailleur
Freehub
Cassette sprocket
Chain
SHIMANO 105
ST-5500-CA / ST-5510 / ST-R600
18
SP40
FH-5500 / FH-5501
CS-HG70-9
CN-HG73
FD-5500 / FD-5501
FC-5501 / FC-5502
BB-5500
RD-5500 /
RD-5501
Bottom bracket cable guide
SM-SP17
t

Shimano ST-R600 Specifications

General

Model	ST-R600
Material	Aluminum
Color	Black
Brake Lever Actuation	Mechanical
Shift Lever Actuation	Mechanical
Clamp Band	23.8-24.2mm
Shift Lever Material	Aluminum
Type	Dual Control Lever
Series	Shimano
Category	Road

Summary

General Safety Information

Operation

Rear and Front Lever Operation

Explains the function of front and rear derailleur levers for shifting.

Rear Derailleur Lever Operation

Details how to operate levers A and B for rear sprocket shifting and quick shifts.

Operation Caution

Highlights critical operational points to prevent incorrect shifting or damage.

Front Derailleur Lever Operation

Explains lever operations for shifting between front chainrings.

Front Derailleur Trimming Operation

Details the noise prevention trimming operation for the front derailleur.

Front Lever Operation Caution

Provides cautions for operating front derailleur levers to avoid improper shifting.

Installation

Handlebar Installation

Details the procedure for securely attaching the shifting unit to the handlebar.

Brake Cable Installation

Outlines the step-by-step process for installing the brake cable and outer casing.

Shifting Cable Installation

Guides on inserting the inner cable and cutting the outer casing for shifting.

Lever Preparation and Outer Stopper Installation

Details preparing levers and installing the outer stopper for cable routing.

Maintenance

Bracket and Lever Disassembly

Step-by-step guide for disassembling the bracket and lever components.

Lever and Bearing Assembly Disassembly

Instructions for taking apart the lever and bearing assembly.

Bracket and Lever Reassembly

Procedure for putting back together the bracket and lever assembly.

Bracket Cover Replacement

Instructions on how to replace the bracket cover correctly.