What to do if unable to adjust welding current by remote controller on Shindaiwa Portable Generator?
If you're unable to adjust the welding current by remote controller on your Shindaiwa Portable Generator, disconnect any AC load connected to the remote control receptacle. Also, ensure the switch (breaker) on the cord reel is turned "ON".
Why is the welding arc weak on my Shindaiwa Welding System?
A weak welding arc on your Shindaiwa Welding System can stem from several issues. Check that the Output Selector Switch is set to 'SINGLE' or 'REGULAR', not 'ECO' or 'DUAL'. Also, ensure the Frequency Switch is at '60Hz', not '50Hz'. Adjust the Current Dial clockwise to increase the current. Poor cable connections can also weaken the arc, so ensure they are securely connected. Verify that the welding cable's diameter and length are appropriate. Make sure there is good contact with the material being welded. Stop using AC output during welding.
What to do if the starter motor will not start on my Shindaiwa Welding System?
If the starter motor on your Shindaiwa Welding System does not start, it could be due to a weak or dead battery. Try recharging the battery first. If that doesn't work, the battery may need to be replaced.
What to do if the engine starts but stalls immediately on my Shindaiwa Welding System?
If your Shindaiwa Welding System's engine starts and then stalls immediately, it could be due to insufficient oil. Replenish the oil. It could also be caused by high water temperature or insufficient coolant/water; maintain the rated coolant/water level. Another possible cause is an inability to charge; in this case, repair is needed.
Why is the welding arc too strong on my Shindaiwa DGW310DMC Welding System?
If the welding arc is too strong on your Shindaiwa Welding System, it might be because the Output Selector Switch is set to 'SINGLE' or 'REGULAR'. Try changing it to 'ECO' or 'DUAL'. Also, the Current Dial position could be too high, so turn it counterclockwise to reduce the current.
How to reduce excessive welding arc on Shindaiwa Portable Generator?
If the welding arc is excessive on your Shindaiwa Portable Generator, the output selector may be set to "SINGLE". Change it to "ECO" or "DUAL". Also, the output control dial position may be incorrect; turn it counterclockwise.
Why is my Shindaiwa Portable Generator emitting excessive black smoke?
If your Shindaiwa Portable Generator is producing excessive black smoke from the muffler, it's likely due to overloaded use. Ensure you operate the machine within its rated output.
What to do if Shindaiwa Portable Generator engine does not stop?
If your Shindaiwa Portable Generator engine won't stop, it may be due to a stop solenoid malfunction. Turn the fuel lever to "CLOSE" to stop the engine and then repair the solenoid.
Why won't my Shindaiwa Portable Generator start?
If your Shindaiwa Portable Generator's engine won't start, several factors could be at play. First, ensure the fuel lever on the fuel filter is open. Secondly, check that you have sufficient fuel. If the fuel is contaminated with water or dust, drain the tank and clean the fuel strainer. Finally, inspect the fuse and repair it if it's burnt.
Why does the slow-down not activate on my Shindaiwa DGW310DMC?
The slow-down feature on your Shindaiwa Welding System might not activate if there's a welding cable short-circuit; repair the short-circuit. Also, if the power consumption of the load is 0.5A or below, the slow-down may not activate; in this case, change the slow-down switch to 'OFF'.
General| Rated Output | 3.1 kVA |
|---|---|
| Frequency | 50/60 Hz |
| Duty Cycle | 60% |
| Engine Type | Diesel, 4-stroke |
| Welding Current Range | 30-310 A |
| Electrode Diameter | 2.0-5.0 mm |
To Next Page
