Tilt (Y) movement
1. Press the Program (3.5) button to enter program mode. The display will show: Program mode.
2. Press the /set Y (3.15) button the LED will blink.
3. Select the fixture(s) you want to control by pressing the Fixture selection buttons (1). The display will
show: Program Mode
Y Channel
4. Move the fader of the channel you wish to use for the Tilt function up and down until the LED blinks.
5. Press the /set Y (3.15) button again to save and exit the programming mode.
Using the jog wheels
The channel assigned to the jog wheel can be controlled by the jog wheel.
1. Press the E/XY (3.14) button, make sure the LED indicator is on.
2. Select the desired fixtures.
3. Control the fixture with the jog wheels.
Setup of slope channels
The channels that have been assigned to the jog wheels will automatically have a slope assigned when
the chase is running. Other channels can be set up with a slope also.
1. Press the Program (3.5) button to enter program mode. The display will show: Program mode.
2. Press the Flash/SlopeSet (3.11) button. The display will show: Slope Channel.
3. Select the desired fixture.
4. Move the channel(s) you wish to assign a slope to. If a channel is assigned, the LED will be lit. If you
made a mistake, press the Release (3.1) button and move the fader you want to release.
5. Press the Flash/SlopeSet (3.11) button again. Now your setup is finished.
Example:
To assign a slope to channel 5 & 6 of fixture 1:
Press Program -> SlopeSet -> Select Fixture 1 -> move the faders of CH5 & CH6 until the LED indicators are
lit. -> SlopeSet. Ok.
Delete
1. Press the Del (3.8) button.
2. Select Scene Page 1 (4.2), Scene Page 2 (4.2), Scene Page 3 (4.2), Chase Page 1 (4.1), Chase Page 2
(4.1) , Chase Page 3 (4.1), Group 1 (4.3), Group 2 (4.3), </SetX (3.15), >/SetY (3.15), or Slopeset (3.11) by
pressing the corresponding button.
3. Press a number 1-16 (4.4) button to select the scene, chase or chasegroup you want to delete. Not
when you have selected </SetX (3.15), >/SetY (3.15), or Slopeset (3.11).
4. Now the Item is deleted.
Example: Delete the chase stored in number button 2 of Chase 1. Press Del -> Chase1 -> 2. Ok.
Create a master control
1. Press the Program button to enter programming mode. The LCD will show: Program mode.
2. Select one of the three master controls by pressing the Dimmer 1 (6.1), Dimmer 2 (6.1) or Dimmer 3
(6.1). button. The display will show: Program mode
Dimmer group: x (Where x stands for the dimmer group number.)
3. Select the fixture(s) you want to use by pressing the corresponding Fixture button (1).
4. Move the faders you like to add in the master control group until the corresponding LED is lit. Repeat
this for all faders yo like to add.
Note: If a fader does not respond, move the fader to the zero position and try again.
5. Press the Dimmer 1 (6.1), Dimmer 2 (6.1) or Dimmer 3 (6.1) button again to save your settings.
Example: We have an 8-channel dimmer pack. The DMX address is 17 which is the start address of the
second fixture in the controller. Follow the steps below to program it into the Dimmer:
Program -> Dimmer1 -> Fixture selection button 2 -> move fader 1-8 until their indicators are lit -> Dimmer1
-> Ok.
Now, a master control is ready. Fader Master1 will control the maximum output of 1–8 in fixture 2.
To Next Page
