Siemens 3100 - Cleaning;Maintenance; Frost protection; Cleaning water inlet filters; Frost protection; Draining the pump

Geaning water inlet filters
Fig
The
water
inlet
filters
must
be
cleaned,
if
There
no
water
or
insultieenit
water
runs
into
the
machine
when
the
waler
tap
is
turned
ON,
The fitters are located in the hase connec-
tion at ihe tap and at the back of the ma-
china.
Cleaning procedure:
1.Turn the water tap OFF.
2.5e1 programme selector to programma
whites/coloureds, namal B and tempera
ture salector to cold. Seith OFF the rma-
chine for 40 seconds to reduce water
pressure in tha supply hosa.
3 Unscrnaw the hose kam the water tem and
rinse the Tilbar oul under running water,
Я4.Бесеппесі tho hosp.
Unscrew the hose at tha back of the ma
Nina
6.Pull the Мег out with flat-nose pliers and
сібап it and ihan replace iL
7 Reconnect iha hose.
В Tum the water tap ON completely and
make sure there arg no banks
9 Tum the water tap OFF
Frost protection
И the machine is located in a room which is
subject to freezing, and residual water in
bath the pump and the water supply hose
must be drainad immediately every irme tiva
machina has been used.
Draining the pump:
See "Cleaning the pump" page 18.
Draining the water supply hose:
T. Turn the water tap OFF.
2 Ипзсгему the hose from the Tap and hold
the end of the hose in а озғаны.
3 Switch ON ап arbitrary wash programma
for approximate 40 seconds. Any ni-
sidual water wall run out of the iniat hose
4 Screw the bose back onto the water tap
Correcting minor problems yourself
| Only qualified technicians are permitted to make repairs on electrical appliances.
Repairs by unauthorised persons can cause considerable damage.
Problana
The power indicator light
does nat come on
Power failure
Washing process does not
start
water not visible during
washing
Poor washing results
Suds come out of the de-
tergent drawer
Foam still visible after last
ringe
Motor moise
Pump пове
Vibrations when washing
and spinning
The machine does not
tumble dry
Machine does пей spin or
does nol pump out tha
water
Possible causes / remedies
- The plug ia nat correctly, or only loosely, inserted in the
Socket.
- A household fuse has blown.
= Power failung.
Н there is a power failure ог the machine malfunctions, an
emergency water discharge procedure is available (see
"Cleaning the pump" pagel, so tha laundry сап be taken
out
"ON/OFF" button not pressed.
Door nat property closed.
This 18 not a mallunction. The water is in the machine be
low the visible level.
Degree of soling was greater than normal.
Change type and amount of detergent,
Select raximurn permissible temperature for fabric typa.
Select a mone powerful wash programma,
Too much detergent was used. Switch OFF the machine
for approximately 5-10 minutes. To reduce foam, put a
tablespoon of fabric softener mixed with 1/2 lier water
into tha detergent drawer. For the next wash adjust iar
amount of detergent accondingly
Certain detergents tend to produce more foam but this
does not altect the ringing rasuti
This is not malfunction, Operating noise can occur at tha
drive motors stari phase,
This is not a malfunction. During its start phase the pump
briefly transports air-producing audible noise. This is nor-
mal
= Transit bolts ware not removed. Follow the directions in
the installation instructions Wage 19)
- The machine's feet were not secured whan tha machinae
was installed. Авайол the machine using a spirit level,
securing the machine 5 feet according to the installation
instructions
= по drying programme set
= по ог too short a drying time set
= tap nat tumad ОМ
-dow nat properly closed
- pump blocked
pump blocked