EasyManua.ls Logo

Siemens 7LF4501-5

Siemens 7LF4501-5
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2514264131-02
3ZW1012-7LF45-7AA0
Betriebsanleitung Operating Instructions Notice d'utilisation Instructivo Istruzioni operative
Instruções de Serviço İşletme kılavuzu Руководство по эксплуатации Instrukcja obsługi 使用说明
EN
DANGER
Hazardous voltage. Will cause death or serious injury.
Turn off and lock out all power supplying this device
before working on this device.
NOTICE
Installation and maintenance must be carried
out by qualified personnel.
DE
GEFAHR
FR
DANGER
Gefährliche Spannung. Lebensgefahr oder schwere
Verletzungsgefahr. Bevor Arbeiten am Gerät durchge-
führt werden, müssen alle Stromquellen ausgeschaltet
und mit einer Einschaltsicherung versehen werden.
Tension électrique dangereuse. Danger de mort ou
risque de blessures graves. Avant d'intervenir sur
l'appareil, couper toutes les sources de tension et les
consigner contre la refermeture.
HINWEIS NOTIFICATION
Installations- und Wartungsarbeiten sind von
qualifiziertem Personal durchzuführen.
L'installation et la maintenance doivent être
effectuées uniquement par des personnes
qualifiées.
ES
PELIGRO
IT
PERICOLO
Tensión peligrosa. Puede causar la muerte o lesiones
graves. Antes de trabajar en este dispositivo, desconecte
y bloquee todas las fuentes que lo alimentan eléctrica-
mente.
Tensione pericolosa. Può causare la morte o lesioni
gravi. Prima di lavorare su questa apparecchiatura, disin-
serire tutte le fonti di alimentazione elettrica dell'appa-
recchiatura ed assicurarle contro la reinserzione.
NOTA NOTA
La instalación y el mantenimiento deben
corre a cargo de personal cualificado.
L'installazione e la manutenzione devono
essere eseguite da personale qualificato.
PT
PERIGO
TR
TEHLİKE
Tensão perigosa. Perigo de morte ou ferimentos gra-
ves. Desligue e bloqueie todas as fontes de alimentação
antes de executar quaisquer trabalhos no aparelho.
Tehlikeli gerilim. Ölüm tehlikesi veya ağır yaralanma
tehlikesi mevcuttur. Cihazda çalışmalar yapılmadan
önce, tüm güç kaynakları kapatılmalı ve bir açma emni-
yetiyle donatılmalıdır.
ATENÇÃO NOT
A instalação e manutenção têm de ser efetua-
das por pessoal qualificado.
Montaj ve bakım işlemleri kalifiye personel
tarafından yapılmalıdır.
РУ
ОПАСНО
РL
ZAGROŻENIE
Опасное напряжение. Опасность для жизни или
телесных повреждений. До начала работы
выключите и заблокируйте все источники питания
этого устройства.
Niebezpieczne napięcie. Niebezpieczeństwo poważ-
nych obrażeń lub utraty życia. Wyłączyć i zablokować
wszystkie źródła zasilania urządzenia przed rozpoczę-
ciem pracy na urządzeniu.
ПРИМЕЧАНИЕ UWAGA
Установка и техническое обслуживание
должны производиться
квалифицированным персоналом.
Instalacja i konserwacja muszą być wy-
konywane przez wykwalifikowany personel.
Technical Support: Internet: http://www.siemens.com/lowvoltage/technical-support
s
Time switch type 1. B. S. T.
Zeitschaltuhr Typ 1. B. S. T.
Interrupteur horaire Type 1. B. S. T.
Programador horario tipo 1. B. S. T.
Orologio interruttore tipo 1. B. S. T.
Temporizador tipo 1. B. S. T.
Zaman saati Tip 1 B. S. T.
Реле времени, тип 1. B. S. T.
Zegar sterujący typ 1. B. S. T.
定时器类型 1. B. S. T.
7LF4501-5 IEC/EN 60730-1
IEC/EN 60730-2-7
Last Update: 21 September 2018
Question and Answer IconNeed help?

Do you have a question about the Siemens 7LF4501-5 and is the answer not in the manual?

Siemens 7LF4501-5 Specifications

General IconGeneral
Product type designation7LF4501-5
Number of channels1
FunctionalityMultifunction
TypeElectronic timer
Time range0.05 s to 100 h
MountingDIN rail
Degree of protectionIP20
FunctionON-delay, OFF-delay
Contact configuration1 CO (SPDT)

Summary

SIEMENS Time Switch Model Identification

English Safety Warnings

Highlights critical electrical hazards and personnel qualifications for safe operation.

Manual Contents and Installation Basics

Assembly and Connection Guide

Provides instructions and diagrams for assembling and connecting the time switch module.

Programming Setup and Modes

Understanding Programming Modes

Details 'Prog NEW' and 'Prog MOD' modes in multiple languages.

Multi-Language Programming Details

Program Configuration and Reset

Device Reset Procedure

Details how to reset the time switch to default factory settings.

Modifying Program Settings

Program Modification and Reset

Instructions for changing existing programs and performing a device reset.

Advanced Program Adjustments

Program Management: Deletion

Deleting Individual and All Programs

Explains how to delete single programs or clear all programmed settings.

Operating Modes and Manual Control

Testing and Verification Procedures

Related product manuals