Siemens iQ700 HM778GM 1 Series - Starting and Interrupting Operations; Setting Operating Modes and Heating

Basic operation en
15
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
1.
To interrupt the operation, press "Stop".
2.
To continue the operation, press "Start".
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
1.
To scroll through the various selection options,
swipe to the left or right on the display.
2.
To select a function, press the corresponding tile.
a Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
3.
If required, press on another tile.
4.
To change the adjustment values:
‒ Swipe over the blue adjustment line or push the
adjustment line to the appropriate point.
‒ Or press and enter the value directly via the
number field that appears.
5.
Use "Start" to start the operation.
6.
If the operation is ended:
‒ If required, you can select other settings and re-
start the operation.
‒ When the food is ready, use to switch the ap-
pliance off.
Tip:You can save your settings as "Favourites" and
use these again.
→"Favourites", Page23
8.6 Setting the type of heating and the
temperature
1.
Press "Types of heating".
2.
Press the type of heating that you want to use.
3.
Set the temperature using the adjustment line or dir-
ectly via the number field ⁠.
If required, you can implement additional settings:
– →"Rapid heating", Page16
– →"Time-setting options", Page16
– →"Microwave", Page17
– →"Ventilation function 'Crisp Finish'", Page19
– →"Meat probe", Page20
4.
Use "Start" to start the operation.
a The appliance starts heating.
a The adjustment values and how long the appliance
has already been in operation are shown on the dis-
play.
5.
When the food is ready, use to switch the appli-
ance off.
Note:The most suitable type of heating for your food
can be found in the type of heating description.
→"Types of heating", Page11
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press "Stop".
2.
Press ⁠.
3.
Press the type of heating that you want to use.
4.
Reset the operation and use "Start" to start.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using the adjustment line
or enter it directly via the number field ⁠.
3.
Press "Apply".
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
1.
Press ⁠.
a If information is available, this is displayed for a few
seconds.
2.
If there is a lot of content, swipe down.
3.
If required, close the notification using ⁠.
8.8 Keeping warm over an extended period
You can use your appliance to keep meals warm for up
to 24 hours without changing the behaviour of the ap-
pliance. Use the time functions and change the basic
settings.
Note:If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
ensure that the behaviour of the appliance is not
changed during operation, only open the appliance
door once the set time has elapsed.
1.
Change the "Lighting" basic setting to "Always off".
→"Basic settings", Page24
2.
Change the "Standby screen" basic setting to "On".
3.
Change the "Signal tone" basic setting to "Very short
duration".
This ensures that the light in the cooking compart-
ment is always off while the appliance is operating
and when you open the appliance door, and the
time display does not change. The duration of the
signal tone is reduced at the end of the operation.
4.
Set the required operating mode.
→"Setting an operating mode", Page15
→"Setting the type of heating and the temperature",
Page15
5.
Set the required cooking time depending on the op-
erating mode.
→"Setting the cooking time", Page16
→"Time-setting options", Page16
6.
Use "End time" to set the time at which the opera-
tion should end.
→"Setting the end time", Page16
→"Time-setting options", Page16
7.
Place the food in the cooking compartment before
the appliance starts to heat.
8.
Start the operation.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.