EasyManuals Logo

Siemens LC28BH542 User Manual

Siemens LC28BH542
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
6
Operation
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Control panel
Control panel
Setting the fan
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
Switching on the appliance
1. Press the # button.
The fan starts at fan setting
ƒ.
2. Press the + or - buttons to set a different fan setting.
Switching off the appliance
Press the
# button.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
1. Press and hold the + button until fan setting appears in the
display panel.
2. Press the + button.
Intensive mode
2 is activated.
3. Press the + button.
Intensive mode
2ƒ is activated.
Note: The run time of the intensive mode is
approx. 6 minutes. Once this time has elapsed, the appliance
switches back to the lower fan setting.
4. Press the - button until the required fan setting is reached.
The intensive mode ends.
Fan run-on time
Press and hold the - button until x appears in the display
panel.
After approx. 10 minutes, the fan switches off automatically.
Lighting
The lighting can be switched on and off independently of the
ventilation.
Press the
A button.
Setting the brightness
Press and hold the
A button until the desired brightness is
reached.
Saturation display
When the metal grease filters or the activated charcoal filter are
saturated, a signal sounds for approx. 4 seconds after the fan
is switched off.
The corresponding symbols appear in the display panel:
Metal grease filter:!
Activated charcoal filter: "
Metal grease filter and activated charcoal filter: ! and "
flash alternately
When this happens, do not delay cleaning the metal grease
filters and/or replacing the activated charcoal filter any further;
see section Cleaning and maintenance and follow the
installation instructions supplied with the accessories.
Resetting a saturation indicator
Press and hold the - button until the saturation indicator no
longer flashes.
The saturation indicator is reset.
Resetting the saturation displays
1. Press and hold the - button until the saturation indicator for
the metal grease filter no longer flashes.
The saturation indicator for the metal grease filter is reset.
2. Press and hold the - button until the saturation indicator for
the activated charcoal filter no longer flashes.
The saturation indicator for the activated charcoal filter is
reset.
Switching over the display for circulating-air mode
For air recirculation mode, the electronic control display must
be switched over accordingly:
1. Check whether the extractor hood is connected and switched
off.
2. Press and hold the % and - buttons at the same time until the
symbol
# is illuminated for the starter set for air
recirculation or the symbol
# is illuminated for the CleanAir
air recirculation module.
The electronic control is switched over to air recirculation.
Switching over the display for exhaust air mode
1. Check whether the extractor hood is connected and switched
off.
2. Press and hold the # and - buttons at the same time until the
symbol
! is displayed.
The electronic control is switched back to air extraction.
Audible signal
Switching on
1. Switch off the fan.
2. Press and hold the # and + buttons until an audible signal
sounds.
The audible signal is switched on.
Switching off
1. Switch off the fan.
2. Press and hold the # and + buttons until an audible signal
sounds.
The audible signal is switched off.
Explanation
#
Fan on/off
- Reduce the fan settings/fan run-on time
+ Increase the fan settings/intensive setting 1, 2
A
Light on/off/dimming

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens LC28BH542 and is the answer not in the manual?

Siemens LC28BH542 Specifications

General IconGeneral
BrandSiemens
ModelLC28BH542
CategoryVentilation Hood
LanguageEnglish

Related product manuals