12 GB
Trimming the hairline
(Precision trimmer attachment
5
)
Use the precision trimmer attachment
5
to shorten and
shape moustache, whiskers, sideburns or eyebrows.
Put the edge of the attachment at the desired hairline height
and move the hair and beard trimmer unit
9
downwards.
Shaving (contours)
(Shaving attachment
4
)
Note: Your skin must be clean and dry. The shaving attachment
4
is only suitable for shaving hairlines.
H
old the hair and beard trimmer unit
9
at a right angle to
the skin surface and gently guide it over your face.
Shave against the direction of your beard growth.
Stretch your skin in complicated areas, such as the chin,
to achieve better results.
Trimming nose and ear hair
(Nose/ear hair trimmer attachment
6
)
(see Fig. J)
Insert only the metal tip slowly into a nostril or an ear.
Slowly move the hair and beard trimmer unit
9
with a
circular motion to trim the hair.
Cleaning with the cleaning brush
Switch the product off using the ON/OFF button
11
.
If cutting attachments (
4
–
8
) or comb attachments
(
1
–
3
) is attached on the product, remove it before
cleaning as described in the chapter “Operation“. Remove
the attachment by pressing the trimmer with your thumbs
from the front (see Fig. A).
Remove the hair remnants from the attachment using the
cleaning brush
21
.
Ordering replacement parts
Replacements for the following parts can be ordered online:
Shaving attachment
4
Precision trimmer attachment
5
Nose/ear hair trimmer attachment
6
Hair trimmer attachment
7
Beard trimmer attachment
8
Item number: 444777_2307
Website: www.optimex-shop.com
Cleaning and care
Never immerse the product, the USB Type A to C cable
16
and the power supply in water or other liquids during corded
use or rinse under running water.
Always switch off the product before cleaning it.
T
he comb attachments
1
,
2
,
3
and nose/ear hair trimme
r
attachment
6
can be cleaned with water. Do not use any
other liquids.
Note: Let them dry before using again.
Do not use aggressive or abrasive cleaning agents.
Wipe down the product with a slightly damp cloth.
If you are not using the product for extended periods,
store it in the storage bag
23
.
Hair and beard trimmer unit
9
Wipe the casing of the hair and beard trimmer unit
9
with
a damp cloth.
Comb attachments
1
,
2
,
3
Remove the comb attachment
1
,
2
,
3
. Rinse the comb
attachment
1
,
2
,
3
with water and let it dry before
using again.
Precision trimmer
5
, hair trimmer
7
and beard
trimmer attachments
8
Remove the attachment from the hair and beard trimmer
unit
9
by pressing it with the thumb towards the rear
(see Fig. A).
Remove the hair remnants from the attachment using the
cleaning brush
21
included in the delivery.
Note: It is recommended that you oil the blades before first
use and after cleaning to guarantee complete functionality
(see Fig. G, H, I). Always switch off the product before oil
the blade. Apply one or two drops of blade oil
20
between
the blades and distribute them evenly. Wipe off any excess
oil with a cloth. You can also use any acid-free oil (such as
sewing machine oil).
Note: The blades can be oiled with or without the comb
attachment
1
,
2
or
3
.
Nose/ear hair trimmer attachment
6
Remove the nose/ear hair trimmer attachment
6
. Rinse it
with water and let it dry completely before using it again.
Shaving attachment
4
Do not detach the shaving foil from the shaving foil frame,
and do not clean it using the cleaning brush
21
.
Note: From time to time, oil the cutting blade with a few
drops of acid- free oil (e.g. sewing machine oil). Attach the
shaving attachment
4
to the hair and beard trimmer unit
9
and let it run for a few seconds without using it. Using a soft
cloth, wipe off the surplus oil, if necessary.
Remove the shaving attachment
4
.
Press the button on the side of the shaving attachment
4
and remove the shaving foil frame. While removing the
shaving foil frame, only hold it at the side and do not press
against the shaving foil.
To Next Page