How to troubleshoot a Simuline Mini Rider 2 that won't power on?
If your Simuline Arcade Game Machine fails to power on, check the following: * Ensure the circuit breaker of the AC unit is operational and connected to AC 230V. * Verify the plugs are correctly connected to the 230V outlet in the cabinet. * Confirm the mains switch of the SCU is turned on.
What to do if Simuline Arcade Game Machines shows Error Code 10C3 90C3?
If your Simuline Arcade Game Machine displays Error Code 10C3 90C3, indicating an over current protection error, follow these steps: 1. Check that the output voltage of the Main Transformer (220R, 220T) remains within the range of 210V~230V. 2. Inspect the actuator for lubrication and apply lubrication if needed, as insufficient lubrication may cause this error.
What to do if Simuline Arcade Game Machines shows Error Code 40C3 DOC3?
If your Simuline Arcade Game Machine displays Error Code 40C3 DOC3, which indicates an over voltage protection error, take these actions: 1. Verify that the output voltage of the Main Transformer (220R, 220T) is within the range of 210V~230V. 2. Check the input power source for any temporary voltage spikes exceeding 240V.
What does error code F800 mean on Simuline Mini Rider 2 Arcade Game Machines?
If your Simuline Arcade Game Machine displays Error Code F800, it means the Motor Drive Board (K5, K8) +12V relay at the input power is disconnected. You should check if the power unit Motor Drive Board input power SMPS +12V is normal. If the SMPS +12V power is normal, check the Motor Drive BD J7 Connector +12V power with a tester. If the +12V power is not available, check the connection harness.
Why is my Simuline Mini Rider 2 Arcade Game Machines cabinet not operating?
If your Simuline Arcade Game Machine cabinet isn't operating, make sure the door is fully closed. Also, check the area sensor; if the YELLOW LED is OFF, remove any obstructions so the YELLOW LED turns ON. Finally, ensure the sensors are properly aligned.
What does error code 90AE 9086 mean on Simuline Mini Rider 2 Arcade Game Machines?
If your Simuline Arcade Game Machine shows Error Code 90AE 9086, it indicates an error with the #1, 2, and 3 Actuators when power is supplied. This can happen if the machine starts in a slanted position. First, try restarting the system. Also, check the installation of the Actuator Limit Sensor (Bottom Sensor) to ensure it is correctly positioned.
What to do if my Simuline Mini Rider 2 fails to power off?
If your Simuline Arcade Game Machine is not powering off, turn off all the powers in the sequence of Emergency Stop, as there may be a malfunction of the system.
What does error code FFFE mean on Simuline Mini Rider 2?
If your Simuline Arcade Game Machine displays Error Code FFFE, indicating that the Actuator Limit Sensor is not responding, first, check the connection and installation of the Actuator Limit Sensor.
What does error code 8C3 mean on Simuline Arcade Game Machines?
If your Simuline Arcade Game Machine shows Error Code 8C3, which indicates a Motor Drive BD “IPM” Error, verify that the AC power to the Motor Drive BD stays within the range of AC200V~AC230V and check the operation of the fan at the Motor Drive BD Heat sink.
What does error code FFFF FFC7 mean on Simuline Mini Rider 2?
If your Simuline Arcade Game Machine displays Error Code FFFF FFC7, and the Motor Drive Board did not receive a signal from the encoder after the power is switched on, first check that the voltage between GND and +5V is within the range of DC5.0V~5.2V.
Explains hazard symbols like Danger, Warning, and Caution.
Explains pictographs like "Handle with Care" and "Protective Earth Terminal".
Defines personnel experienced in amusement equipment maintenance.
Defines personnel involved in amusement equipment manufacturing or design.
Provides warnings related to handling, cleaning, and static electricity.
Details various warning labels applied to the product.
Outlines restrictions and requirements for product installation and use.
Safety instructions for the end-user during operation.
Identifies components of the main body of the product.
Details the front components of the System Console Unit.
Describes the Operator Panel and its functions.
Details the rear components of the System Console Unit.
Describes the Motion Control Unit and its connections.
Steps for unpacking the product and handling the crate.
Instructions for installing the pillar frames of the main structure.
Steps for assembling and installing the actuator frame.
Instructions for attaching and securing the cabin.
Details on connecting the cabin harness and other wiring.
Lists tools required for moving the product.
Instructions for attaching casters for mobility.
Describes the function of the area sensor.
Explains the game stop and emergency stop button functions.
Details the safety belt and its function.
Instructions to follow before starting a ride.
Steps for choosing and initiating a ride.
Procedures for turning the system on and off.
Instructions for activating the emergency stop.
How to configure system settings.
Safety precautions for handling the product's monitor.
Guide to adjusting monitor display parameters.
Procedures for greasing actuators and joints.
Schedule and guidelines for regular maintenance inspections.
Table listing common problems, causes, and countermeasures.
Explains MCU error codes and their solutions.
Diagram and list of parts for the Mini Rider 2.
General| Category | Arcade Game Machines |
|---|---|
| Model | Mini Rider 2 |
| Manufacturer | Simuline |
| Type | Motion Simulator |
| Monitor | LCD |
| Input Method | Pedals |
| Game Features | Motion |
| Power Supply | AC 220V |
To Next Page
