SIPOS AKTORIK 2SA7 Series - User Manual

1
Issue: 05.19 SIPOS Aktorik GmbH Y070.485/EN
Subject to changes without notice!
1
Contents
1 General information ��������������������������������� 1
1.1 Safety information ................................... 1
1.2 Transport and storage ............................. 2
1.3 Disposal and recycling ............................ 2
EU Declaration of conformity ........................... 2
2 Assembly and connection
���������������������� 2
2.1 Mount to valve/gear ................................. 2
2.2 Separate mounting .................................. 4
2.3 Remote control unit ................................. 4
2.4 Electrical connection ............................... 4
3 Operation
��������������������������������������������������� 5
3.1 Manual operation ..................................... 5
HiMod
PROFITRON
1 General information
1�1 Safety information
General information
The devices referred to in this document are components of installations conceived for industrial
applications. They are designed in accordance with the recognized engineering rules.
All work involved in transport, assembly, installation, commissioning, maintenance and repair has
to be performed by qualied personnel.
Qualied personnel within the meaning of the relevant safety instructions of this documentation
are all persons authorized to perform the required tasks according to the standards of safety
technology and who may recognize and avoid potential hazards. They must be thoroughly familiar
with the warnings at the device and the safety instructions of these operation instructions.
Introduction
These operation instructions contain concise information required for assembly, operation and
commissioning. Extensive operation instructions for PROFITRON/HiMod are available on the
Internet: www.sipos.de ►
►Product documents ►Instruction manuals.
■
Leakage currents
As standard, the leakage current of the actuators exceeds 3.5 mA. Therefore, xed
installation in accordance with IEC 61800-5-1 is required.
■
Residual current circuit breaker or monitoring devices
Due to the integral frequency converter, a direct current within the protective ground-
ing conductor can be generated.
Should a residual current-operated protective (RCD) or monitoring (RCM) device be
used upstream the network, it must be of type B.
The distribution of this product is restricted according to IEC 61800-3.
and may cause radio interferences in domestic environments. In this case it may be necessary to
take additional measures.
The following is of particular importance:
■
The technical data and indications on permissible use (assembly, connection, environmental
and service conditions).
■
The general installation and safety guidelines as well as the local, plant-specic provisions and
requirements.
■
The proper use of tools and lifting and transport equipment.
■
The use of personal protective equipment, especially in high ambient temperatures and with
potential high actuator surface temperatures.
Prior to starting the assembly:
■
Make sure that the intended measures (possible operation of the valve, etc.) are not likely to
cause any injuries to persons or to interfere with the equipment.
■
Heed the local ambient conditions, in particular the vibration load, which can be caused when
mounting an actuator to a vibrating valve.
Should supplements be required for certain versions, applications, environmental conditions or
software functions of the actuator, they will be included within the scope of delivery.
Operation instructions
Assembly, operation and commissioning
of
2SA7, 2SQ7
electric actuators
3.2 Indications of the LEDs ........................... 6
3.3 Status indication ...................................... 6
3.4 Display – position bar .............................. 6
3.5 Navigation through the menus ................ 6
4 Commissioning
���������������������������������������� 7
4.1 User management ................................... 7
4.2 End position adjustment .......................... 8
4.3 Mech. position indicator adjustment ...... 10
5 Maintenance, inspection, service
������� 10
5.1 General safety information .................... 10
5.2 Notes on inspection ............................... 10
5.3 Spare parts ............................................ 10

SIPOS AKTORIK 2SA7 Series Specifications