EasyManua.ls Logo

Skil 1400 - Tool Lubrication; Carbon Brushes; Maintenance; Extension Cords

Skil 1400
44 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
/ *7 .A=.7<287 ,8;- 2<
7.,.<<*;B * ,8;- @2=1
*-.:>*=.<2C.,87->,=8;<=1*=2<,*9*+5.
8/,*;;B270=1.,>;;.7=7.,.<<*;B/8;B8>;
=885 6><= +. ><.- This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-
wire extension cords that have 3-prong plugs
and receptacles.
# The smaller the gauge number, the
heav i er the cord.
!")"'#"!"
%##!#$!!##"
!
WARNING
#885E<
69.;.
!*=270
8;-"2C.27&
&2;."2C.<2766
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
8;-.70=127..= 8;-.70=127.=.;<
A=.7<2878;-<
".;?2,.
;.?.7=2?. 6*27=.7*7,.
9.;/8;6.- +B>7*>=18;2C.-
9.;<877.5 6*B ;.<>5= 27 62<95*,270 8/
27=.;7*5 @2;.< *7- ,86987.7=< @12,1
,8>5- ,*><. <.;28>< 1*C*;- We
recommend that all tool service be performed
by a Skil Factory Service Center or Autho rized
Skil Service Station.
#$!#
Your Skil tool has been properly lubricated
and is ready to use. It is recommended that
tools with gears be regreased with a special
gear lubricant at every brush change.
!!$""
The brushes and commutator in your tool
have been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend every
two to six months the brush es be examined.
Only genuine Skil replace ment brushes
specially designed for your tool should be
used.
!"
Bearings which become noisy (due to heavy
load or very abrasive material cut ting) should
be replaced at once to avoid overheating or
motor failure.
5.*7270
#8*?82-*,,2-.7=< *5@*B<
-2<,877.,= =1. =885 /;86
=1. 98@.; <>995B +./8;. ,5.*7270 8;
9.;/8;6270*7B6*27=.7*7,. The tool may
be cleaned most effectively with compressed
dry air. 5@*B<@.*;<*/.=B 08005.< @1.7
,5.*7270=885<@2=1,869;.<<.-*2;
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not at tempt to clean by inserting pointed
objects through openings.
.;=*27 ,5.*7270 *0.7=<
*7- <85?.7=< -*6*0.
95*<=2, 9*;=< Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
*27=.7*7,.
!
WARNING
!
WARNING
!
CAUTION
-12-
SM 1619X05148 10-10:SM 1619X05148 10-10 10/12/10 9:43 AM Page 12