EasyManuals Logo

SkyLink 39 User Manual

SkyLink 39
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Group Brand Brand jumpers setting Proceed to
A B
1 Chamberlain
®
, Sears
®
, Lift-Master
®
- +
(without DIP switches but with red, orange or green
learn button)
2 Chamberlain
®
, Lift-Master
®
, Sears
®
, Wayne Dalton
®
, 0 -
Master Mechanic
®
(without DIP switches but with
yellow, white, or gray learn button)
3* Genie
®
Intellicode
TM
* (without DIP switches) + +
4 Genie
®
(with DIP switches), Overhead
®
0 +
5 Chamberlain
®
, Lift-Master
®
, Sears
®
, Wayne Dalton
®
, + -
Master Mechanic
®
(with DIP switches)
6 Stanley
®
, Multi-Code
®
, Martec
®
- -
7 Linear
®
, Moore-O-Matic
®
+ 0
8 Pulsar
®
, Allstar
®
, Allister
®
, Linear
®
MegaCode
TM
- 0
1a. Locate frequency
switch on the top of
the transmitter:
(See diagram A)
Code connector Location
1b. Determine the brand of your garage
door opener and set the frequency
switch to the corresponding position.
(See chart 1)
A B C D
2a. To set the brand
jumpers, open the
case with a coin
(see diagram B).
Brand
Jumper
Chart 1
Diagram B
STEP 1 - SET FREQUENCY SWITCH
BATTERY
A = “+”
B = “-”
Diagram C
REMOVE JUMPER = “0”
4c. If the connector is placed on the top and middle posts, that
column is set on “ + ” or “ON” or “CLOSE”. If the connector
is placed on the middle and bottom posts, that column is
set on “ - ” or “OFF” or “OPEN”. If the connector is removed
completely, (not placed on any posts), it is set to “ 0 ” or the
neutral position. (see
diagram G for examples
of how to set a column
to the three different
positions). When re-
moving a connector to
set a column to the
neutral position, save
the connector in case
you change the code
at a later date.
STEP 4 - SET CODE CONNECTORS
STEP
2 - SET BRAND JUMPERS
2b.The Model 39 contains 2 brand jumpers and 12 code
connectors (see diagram C). The brand jumpers are
located just above the battery with markings “A” and
“B”. There are 2 connectors, one is placed on the “A”
column, the other one is placed on the “B” column.
For each column, there is a connector. If the connector
is placed on the top and middle post of that column,
that column is set on “+”. If the connector is placed
on the middle and bottom posts, that column is set on
“-“. If the connector is removed completely, that column
is set on “0” (see diagram C). In order for the Model
39 to work with your existing garage door opener
(motor), you need to set the brand jumpers based on
the brand of your existing garage door opener. Please
set these 2 brand jumpers “A” and “B” based on the
brand jumpers setting on chart 2. Please identify the
group number on chart 2 in order to determine which
is the next step to proceed.
Chart 2
* Note:
For Genie
®
Intellicode
TM
, if the brand jumper for group 3 cannot operate your garage door
opener properly, please use setting A “+”, B “-”.
‘+’ or ‘ON’ or CLOSE
‘0’ = BLANK
‘-’ or ‘OFF’ or ‘OPEN’
Diagram G
Diagram A
PROGRAMMING THE TRANSMITTER
Thank you for your purchase of the Skylink garage door remote
control, Model 39. There are 3 different steps you need to setup in
order to use this universal garage door remote control to operate
your existing garage door opener. These 3 steps are:
1) Frequency switch – select the correct frequency according to
the brand of your existing garage door opener. Refer to Step 1.
2) Brand jumpers – place the brand jumpers at the correct posi-
tion according to the brand of your existing garage door opener.
Refer to Step 2.
3) Code setting – Set the jumper connectors on the Model 39 so
that they match the code setting of your existing garage door
opener. Refer to Step 3 or Step 4 depending on the brand of
your garage door opener.
Please follow the detailed instructions below in order to setup the
Skylink Model 39 to work with your existing opener.
USA
CANADA
A
390
390
B
318
318
C
310
315
D
300
310
For garage door openers
belonging to groups 1
to 3, please follow step 3
of the procedures, this will
complete the setup. No
need to proceed to step 4.
For garage door openers
belonging to groups 4
to 8, you can proceed
directly to “Step 4 – Set
Code Connector” after
you have successfully set
the brand jumpers. Please
skip step 3 below.
STEP 3 - LEARN CODE
Proceed
to Step 3.
Proceed
to Step 4,
skip Step 3.
Chamberlain
®
Lift-Master
®
Sears
®
Wayne Dalton
®
Master Mechanic
®
Genie
®
Overhead
®
Pulsar/Allister/Allstar
®
Linear
®
MegaCode
TM
Linear
®
M-O-M
®
Stanley
®
Multi-Code
®
Martec/Teckey
®
Skylink
®
UR-100
390
390
390
300/390
390
390
390
318
318
310
310
310
300/310
300
390
Brand of your opener
Set switch
to position
Frequency
USA
A
A
A
D/A
A
A
A
B
B
C
C
C
D/C
D
A
Set switch
to position Frequency
CANADA
C/A
C/A
C/A
C/A
C/A
C/A
A
B
B
D
D
D
D
-
A
315/390
315/390
315/390
315/390
315/390
315/390
390
318
318
310
310
310
310
-
390
Diagram F
Diagram E
Note:
Proceed to this step only if the brand of your garage door opener belongs to
either group 4, 5, 6, 7 or 8 on chart 2. Otherwise, proceed to Step 3 - Learn code.
4a. If the brand of your garage door opener belongs to groups 4 to 8,
that means
you need to program the correct code setting in order for the Model 39 to
work with your existing garage door opener. There are 12 code connectors on
12 columns from 1 to 12 (see diagram E). Each column has one connector.
(see diagram F)
4b. Set the connectors numbered 1 through 12 to match the code setting of your
existing transmitter or receiver. There are 2 places you can find out the code
setting from a column of small switches of your existing garage door opener.
1) your existing transmitter (the unit you currently use to open your garage).
2) the receiver of your garage door
opener (the unit with the motor
mounted on the ceiling of your
garage).
Note:
Proceed to this step only if the brand of your garage door opener belongs
to either group 1, 2 or 3 on chart 2. Otherwise, proceed to Step 4 - Set
code connector.
3a. If your existing garage door opener belongs to any brand from group 1,
2 or 3, then you should find a “learn” button from the garage door opener
(the unit with the motor located on the ceiling of your garage, see dia-
gram D). Press this learn button for approximately 2 seconds. The
LED light beside the learn button will go on and then press the button
on the Model 39 to activate it. The LED light on the garage door opener
will flash then go off.
The Model 39 is now programmed
to your existing garage door opener
and will operate your garage door.
Programming is now completed
and please refer to the “Battery”
section of this manual for battery
maintenance.
Diagram D
‘Learn’ Button
Garage Door
Opener (GDO)
STEP 2 - SET BRAND JUMPERS

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the SkyLink 39 and is the answer not in the manual?

SkyLink 39 Specifications

General IconGeneral
BrandSkyLink
Model39
CategoryRemote Control
LanguageEnglish

Related product manuals