9
12
10
13
11
14
www.smartmiglobal.com
Intelligent Control with Apple HomeKit
Open the Home app on your iPhone/iPad.
Tap "Add Accessory" and then scan the HomeKit setup code on the product sticker
(two stickers on the device unit, see illustration), or enter the eight-digit setup code
above the HomeKit Setup Code. The device will then be linked to the Apple Home
app.
The device can be linked to Smartmi
Link after linking to HomeKit. Go to
the Personal Info page on Smartmi
Link. Tap "HomeKit Info" and then link
the HomeKit device as prompted.
Devices linked to Smartmi Link can
also be added to HomeKit. Go to the
Device Control page on Smartmi Link.
Tap "Add to HomeKit" in "Settings"
and then link the device to HomeKit
as prompted.
Note:
Please ensure that your Wi-Fi network is both
available and has Internet access. Place your
phone as close to this product as possible. (This
product does not support 5G networks).
To control this accessory which is compatible
with HomeKit, it is recommended to use iOS
13.0 or a later version.
Please keep the HomeKit setup code, as you
will need to scan the code to link the device to
HomeKit after a factory reset.
iPad and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Controlling this HomeKit-enabled accessory
automatically and away from home requires a
HomePod, Apple TV, or iPad set up as a home
hub. It is recommended that you update to the
latest software and operating system.
1
2
HomeKit Setup Code
When your phone connects to the purifier for the first time or if
your phone fails to connect, hold down the buttons " " and " "
simultaneously for 5 seconds. The Wi-Fi icon on the screen will
flash. When you hear a sound, the Wi-Fi module has been reset
successfully.
Resetting Wi-Fi Resetting Purifier
Hold down the buttons " " and " " simultaneously for 10
seconds. After you hear a sound, the purifier has been reset
successfully.
Filter Status Reminder Replacing and Resetting the Filter
1
Turn over the purifier and remove the
filter by rotating it counterclockwise.
2
Replace the filter by following the
instructions contained in the user
manual.
Resetting the Filter
After replacing the filter and turning on
the purifier, hold down " " for 5 seconds.
When you hear a sound, it indicates the
purifier has restarted the filter replacement
count.
Note: Power off purifier and disconnect it
from the power supply before performing
the following operations.
Note: Timely replacement of the filter once the
recommended filter life is over is advised. Once
the Pet Allergy Filter replaced, which contains
activated carbon, the filter will retain the odor of the
harmful gases it has absorbed, when saturated,
put the used filter in a place with sunshine and
ventilation to recover partial performance.
Filter Replacement Reminder
2
Filters should be replaced every 6–12
months. The app will send a reminder
when the filter's lifespan reaches 10% or
less.
Once filter life drops below 10%, the power
button will blink every time you turn on the
machine. Please replace the filter as soon
as possible to ensure normal operation and
optimal air purification.
How to Buy the Filter
Scan the QR Code or
Visit smartmi's online store
https://www.smartmiglobal.com
for more information.
Click on the product page on the app and
check the filter level, which will be displayed
as a percentage.
Checking Filter Lifespan
1
3
3
4
2
2
1
1
Maintenance and Care
Power off purifier and disconnect it from the power supply before performing the following operations.
Cleaning the Filter Housing
Turn over the purifier and remove the
filter by rotating it counterclockwise.
Use a vacuum cleaner to remove dust
from the ventilation hole and cabin
walls, or wipe them using a soft cloth.
Re-install the filter after it has been
cleaned.
Note: Do not spray liquid onto the purifier's
casing, or wipe it using a wet cloth. This
could lead to drops of water leaking into the
base of the device.
Cleaning Laser Particulate
Matter Sensor
Turn over the purifier and remove the
filter by rotating it counterclockwise.
Use a screwdriver to loosen the
screws on the sensor cover.
Remove the cover and clean it with a
hair dryer or pneumatic air gun.
Once cleaning is finished, fix the cover
back onto the sensor and tighten the
screws.
Note: Do NOT clean with hot air.
Linking the Device
to Smartmi Link
This product has been linked to the
Smartmi Link and can be controlled using
the app.
Scan the QR code or search for "Smartmi
Link" on the app store to download and
install the app. Go to the app's homepage,
click "+" in the middle of the page, then add
the device as prompted.
Note:
Please ensure that your Wi-Fi network is both
available and has Internet access. Place your
phone as close to this product as possible. (This
product does not support 5G networks)
This product will be listed as "Smartmi Air
Purifier P1" in the app's device listing.
Specifications
Smartmi Air Purifier P1 User Manual
Pollen
*Standards: Q/BJZMK0001-2018
**ANSI/AHAM AC-1-2019
Name Smartmi Air Purifier P1 Rated Voltage 24V
Model ZMKQJHQP11 / ZMKQJHQP12 Rated Power 30W
Item Dimensions Φ220 × 360.5 mm Power Supply Unit Input 100-240V~ 50/60Hz 1.0A
Net Weight Approx. 3 kg
Clean Air Delivery Rate
(CADR Particles)
250 m³/h
Recommended Surface 17.5–30 m
2
* Pollen CADR 150cfm **
Dust CADR 130cfm ** Smoke CADR 120cfm **
Wireless Connectivity Wi-Fi IEEE 802.11 b/g/n 2.4GHz
Contains FCC ID : 2ANDL-TYWE3SE
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Limited by local law regulations, version for North America does not have region selection option.
To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of
this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
210429-Y
Manufactured by: Beijing Smartmi Electronic Technology Co., Ltd.
Address:Room 201-203, Unit 6, Building A, No. 66,Zhufang Road, Qinghe, Haidian District, Beijing
For detailed e-manual, please go to https://www.smartmiglobal.com/pages/manual
For more information, please visit: https://www.smartmiglobal.com/
Need support? Please contact smartmi customer service: onlinesupport@smartmiglobal.com
To Next Page
Need help?
General
