F
13
Note) When using the negative COM specification, use valves for negative COM.
Cable assembly
Electrical wiring specifications
1(–) (+) Black None
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
14
(–) (+) Yellow Black
Station 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
Station 10
Station 11
Station 12
2
(–) (+) Brown None
15
(–) (+) Pink Black
3
(–) (+) Red None
16
(–) (+) Blue White
4
(–) (+) Orange None
17
(–) (+) Purple None
5
(–) (+) Yellow None
18
(–) (+) Gray None
6
(–) (+) Pink None
19
(–) (+) Orange Black
7
(–) (+) Blue None
20
(–) (+) Red White
8
(–) (+) Purple White
21
(–) (+) Brown White
9
(–) (+) Gray Black
22
(–) (+) Pink Red
10
(–) (+) White Black
23
(–) (+) Gray Red
11
(–) (+) White Red
24
(–) (+) Black White
12
(–) (+) Yellow Red
25
(–) (+) White None
13
(+) (–) Orange Red
Polarity
Terminal
no.
Lead wire
color
Dot
marking
Positive
COM
spec.
Negative
COM
spec.
D-sub connector
Lead wire colors for
D-sub connector assemblies
(AXT100-DS25- )
As the standard electrical wiring specification
used is for 12 stations or less, double wiring
(connected to SOL. A and SOL. B) is used for
the internal wiring of each station regardless
of valve and option types.
Mixed single and double wiring are available
as options.
Refer to special wiring specifications (options)
below.
Mixed single and double wiring are available as
options. The maximum number of manifold stations
is determined by the number of solenoids. Count one
point for a single solenoid type and two points for a
double solenoid type. The total number of solenoids
(points) must not exceed 24.
015
030
050
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Connector terminal no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
COM
(For 25P)
D-side
1 2 3
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
stations
AXT100-DS25-
015
030
050
Lead wire colors for
D-sub connector
cable assembly
terminal numbers
Terminal
no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Lead
wire
color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot
marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
D-sub connector cable assemblies (optional)
Electrical characteristics
Cable
length (L)
Part no.
Note
1.5m
3m
5m
AXT100-DS25-015
AXT100-DS25-030
AXT100-DS25-050
Cable
0.3mm² x 25 cores
Item
Characteristic
Conductor resistance
Ω/km, 20°C
Withstand pressure
V, 1 minute, AC
Insulation resistance
MΩ/km, 20°C
65 or less
1000
5 or more
Some connector manufacturers:
• Fujitsu, Ltd.
• Japan Aviation Electronics Industry, Ltd.
• J.S.T. Mfg. Co., Ltd.
• HIROSE ELECTRIC CO., LTD.
Cable
0.3mm² x 25 cores
O.D. ø1.4
Seal (length indication)
Connector DB-25SF-N
manufactured by
Japan Aviation
Electronics Industry, Ltd.
Socket side
Terminal no.
Approx. ø10
47.04
55
16
44
8(2.4)
L
1⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅13
14⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅25
Molded cover
2-M2.6 x 0.45
SMC
015
Special wiring specifications (options)
• Using our D-sub connector for electrical connections greatly reduces labor,
while it also minimizes wiring and saves space.
• We use a D-sub connector (25P) that conforms to MIL standards and is
therefore widely compatible with many standard commercial models.
• Top or side entry for the connector can be changed freely, allowing for
changes even after mounting, to meet any changing needs for space.
D-sub connector cable assemblies can be ordered with manifolds.
Refer to manifold ordering.
∗ When using a standard commercial
connector, use a type 25P female connector
conforming to MIL-C-24308.
∗ Cannot be used for transfer wiring.
Note) The minimum bending
radius for D-sub connector
cables is 20mm.
U-side
Note)
VQC1000/2000
Kit (D-sub Connector Kit)
Conforms to IP40
To Next Page
Loading...
