SMC Networks VQC1000 Series - VQC1000;2000 Flat Ribbon Cable Kit; Electrical Wiring Specifications; Flat Ribbon Cable Assembly Options

VQC1000/2000
Kit (Flat Ribbon Cable Kit)
Conforms to IP40
P
15
Cable assembly
Electrical wiring specifications
Mixed single and double wir-
ing are available as options.
The maximum number of
manifold stations is deter-
mined by the number of sol-
enoids. Count one point for a
single solenoid type and two
points for a double solenoid
type. The total number of
solenoids (points) must not
exceed 24.
D-side
1 2 3
⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅
stations
AXT100-FC -
1
2
3
20
26
Flat ribbon cable connector assemblies (optional)
Cable
length (L)
Part no.
1.5m
3m
5m
26P
AXT100-FC26-1
AXT100-FC26-2
AXT100-FC26-3
20P
AXT100-FC20-1
AXT100-FC20-2
AXT100-FC20-3
Some connector manufacturers:
• HIROSE ELECTRIC CO., LTD.
• Sumitomo/3-M Limited
• Fujitsu, Ltd.
• Japan Aviation Electronics Industry, Ltd.
• J.S.T. Mfg. Co., Ltd.
• Oki Electric Cable Co., Ltd.
6
(15.6)
L
Terminal no.
Red
28AWG
30 (20P)
37.5 (26P)
26 2 25 1
Note) When using the negative COM specification, use valves for negative COM.
Flat ribbon cable connector
<26P> <20P>
Connector terminal number
26
24
22
20
18
16
14
12
10
8
6
4
2
25
23
21
19
17
15
13
11
9
7
5
3
1
Triangle mark indicator position
Double wiring (connected to SOL. A
and SOL. B) is used for the internal
wiring of each station regardless of
valve and option types.
Mixed single and double wiring are
available as options.
Refer to special wiring specifica-
tions (options) below.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
COM
Station 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
COM
Station 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
Station 10
Station 11
Station 12
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(–)
(–)
Terminal
no.
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(+)
(+)
Polarity
Positive
COM
spec.
Negative
COM
spec.
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(–)
(–)
Positive
COM
spec.
Negative
COM
spec.
26
24
22
20
18
16
14
12
10
8
6
4
2
25
23
21
19
17
15
13
11
9
7
5
3
1
COM COM
(For 26P)
20
18
16
14
12
10
8
6
4
2
19
17
15
13
11
9
7
5
3
1
COM COM
(For 20P)
Special wiring specifications (options)
U-side
• Using our flat ribbon cable for electrical connections greatly reduces
labor, while it also minimizes wiring and saves space.
• We use flat ribbon cables whose connectors (26P and 20P) conform
to MIL standards, and are therefore widely compatible with many
standard commercial models.
• Top or side entry for the connector can be changed freely, allowing
for changes even after mounting, to meet any changing needs for
space.
Terminal
no.
Polarity
Type 26P flat ribbon cable connector assemblies can be ordered
with manifolds. Refer to manifold ordering.
∗ When using a standard commercial connector, use a type 26P
connector conforming to MIL-C-83503 or a type 20P with strain relief.
∗ Cannot be used for transfer wiring.