Smeg LBS106F2 - Starting and Managing Cycles; Starting a Wash Programme; Child Lock Functionality; Door Lock and Mid-Cycle Changes

31
EN
ProgrammeSelectionknobtoanyprogramme.
Thus,DelayedStartfunctionwillbecanceled.The
End/Cancellightflashescontinuously.Then,select
theprogrammeyouwanttorunagain.PressStart
/Pausebuttontostarttheprogramme.
Starting the programme
PressStart/Pausebuttontostarttheprogramme.
Programmefollow-uplightshowingthestartupof
theprogrammewillturnon.
C
 Ifnoprogrammeisstartedornokeyis
pressedwithin1minuteduringprogramme
selectionprocess,themachinewillswitch
toPausemodeandtheilluminationlevelof
thetemperature,speedandloadingdoor
indicatorlightswilldecrease.Otherindicator
lightsandindicatorswillturnoff.Oncethe
ProgrammeSelectionknobisrotatedor
anybuttonispressed,indicatorlightsand
indicatorswillturnonagain.
Child Lock
Usechildlockfunctiontopreventchildrenfrom
tamperingwiththemachine.Thusyoucanavoid
any changes in a running programme.
C
 IftheProgrammeSelectionknobisrotated
whenthechildlockisactive,thelightsonthe
1
st
and 2
nd
auxiliaryfunctionbuttonswillblink
3times.Thechildlockdoesnotallowany
change in the programmes and the selected
temperature,speedandauxiliaryfunctions.
C
 Evenifanotherprogrammeisselectedwith
theProgrammeSelectionknobwhiletheChild
Lockisactive,previouslyselectedprogramme
willcontinuerunning.
C
 WhentheChildLockisactiveandthe
machineisrunning,youcanswitchthe
machinetoPausemodewithoutdeactivating
theChildLockbyturningtheProgramme
SelectionknobtoOn/Offposition.When
youturntheProgrammeSelectionknob
afterwards,theprogrammewillresume.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
AuxiliaryFunction
buttonsfor3seconds.Thelightsonthe1
st
and 2
nd
AuxiliaryFunctionbuttonswillflashwhileyoukeep
thebuttonspressedfor3seconds.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliaryfunction
buttonsfor3secondswhileanyprogrammeis
running. The lights on the 1
st
and 2
nd
Auxiliary
Functionbuttonswillflashwhileyoukeepthe
buttonspressedfor3seconds.
C
 Inadditiontothemethodabove,todeactivate
theChildLock,switchtheProgramme
SelectionknobtoOn/Offpositionwhenno
programmeisrunning,andselectanother
programme.
C
 Whenthepowerisrestoredafterapower
failureorafteryourmachineisunplugged
andpluggedinagain,theChildLockwillnot
bedeactivatedwhenthemachineresumes
operating.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.At
thebeginningofeveryprogrammestep,the
relevantindicatorlightwillturnonandlightofthe
completedstepwillturnoff.
Youcanchangetheauxiliaryfunctions,speed
andtemperaturesettingswithoutstoppingthe
programmeflowwhiletheprogrammeisrunning.
Todothis,thechangeyouaregoingtomakemust
beinastepaftertherunningprogrammestep.If
thechangeisnotcompatible,relevantlightswill
flashfor3times.
C
 Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactive
ortheautomaticunbalancedloaddetection
systemmightbeactivatedduetothe
unbalanceddistributionofthelaundryinthe
machine.
Loading door lock
Thereisalockingsystemontheloadingdoorof
themachinethatpreventsopeningofthedoorin
caseswhenthewaterlevelisunsuitable.
Loadingdoorlightwillstartflashingwhenthe
machineisswitchedtoPausemode.Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadily
within1-2minutesandtheloadingdoorcanbe
opened.
Ifthelevelisunsuitable,LoadingDoorlightturns
offandtheloadingdoorcannotbeopened.If
youareobligedtoopentheLoadingDoorwhile
theLoadingDoorlightisoff,youhavetocancel
thecurrentprogramme;see"Cancelingthe
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthe
machinetopausemodewhileaprogrammeis
running.Thelightofthestepwhichthemachine
isinstartsflashingintheProgrammeFollow-up
indicatortoshowthatthemachinehasbeen
switchedtothepausemode.
Also,whentheloadingdoorisreadytobeopened,
LoadingDoorlightwillalsoilluminatecontinuously
in addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Depending on the step the programme has
reached,youmaycanceloractivatetheauxiliary
functions;see,"Auxiliaryfunctionselection".
You may also change the speed and temperature
settings;see,"Spinspeedselection"and
"Temperatureselection".
C
 Ifnochangeisallowed,therelevantlightwill
flashfor3times.