Snapper 7800428 User Manual

Handles and Controls
Footnotes:
Manual No. 700647721"STEEL DECK WALK BEHIND MOWERS
SERIES 20
5
Part No Descri
p
tionItem Qty
1 7074411 1 HANDLE, Upper
2 7074156 1 HANDLE, Middle
3 7033985 1 HANDLE, Lower LH (Adjustable)
4 7033986 1 HANDLE, Lower RH (Adjustable) used on 7800430 & 7800492
5 7074418 1 BAIL, OPC Control
6 7034872 1 CLIP, Zone Control
7 7034608 1 * CABLE, Zone Control (52-63/64” Long) used on 7800425, 7800428, 7800437, 7800596,
7800597 & 7800602
7 7102593 1 * CABLE, Zone Control (52-21/32” Long) used on 7800424, 7800552, 7800553, 7800554 &
7800555
7 7078078 1 * CABLE, Zone Control (50-31/64” Long) used on 7800427 & 7800432
8 7074473 1 HANDLE, Clutch
9 7028407 1 GRIP, International Symbol
10 7034604 1 CABLE, Clutch Control (41-1/4” Long)
11 7012121 1 COVER, Vinyl
12 7012122 1 SPRING, Clutch - 21S
13 7074003 1 BRACKET, Shift
14 7024641 2 TIE, Wire, 1.29 long, black
15 7073822 1 BRACKET, Bell Crank
16 7013849 1 SPACER, .33 x .63 x .156
17 7073913 1 BELL CRANK
18 7074140 1 CONTROL PANEL (w/o Electrical Switch Hole) Used on Manual Start Models
18 7074469 1 CONTROL PANEL (w/Electrical Switch Hole) Used on electric start models
18 7073826 1 CONTROL PANEL (w/o wheel drive slot) used on 7800428, 7800437 & 7800596
19 7900067 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
20 7091130 2 WASHER, .33 x .88 x .09 Flat
21 7091904 1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5
22 7090538 1 TEENUT, 5/16-18
23 7012114 1 BUSHING, Differential, .328 x .625 x .41
24 7090595 2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR 5
25 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
26 7091575 1 NUT, 5/16-18 Hex Center Lock
27 7074113 1 LEVER, Shift
28 7091606 1 NUT, 5/16-24 Hex Center Lock GR 5
29 7023813 1 CLIP, Wiring Harness
30 7091189 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2
31 7035744 4 KNOB, 5/16-18 Wing (Black)
31 720727 4 KNOB, 5/16-18 Wing (Black) Briggs part
32 7079577 2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap GR 5
33 7090053 5 WASHER, 1/4” Internal Tooth Lock
34 7091576 3 NUT, 1/4-20 Hex
35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
36 7014343 2 BUSHING, .27 x .35 x .4 Flange
37 7023792 1 PIN, 1/4 x 1-1/2”
38 7091020 1 PUSH-NUT, 1/4”
NOTE: * Part number and revision is stamped on cable.
Not for
Reproduction

Snapper 7800428 Specifications

General

Brand	Snapper
Model	7800428
Category	Lawn Mower
Language	English