48" MOWER DECK ASSEMBLY (Part 2)
Footnotes:
TP 400-5049-1-HZ-N
Manual No. 7006181SCRAMBLER ZERO-TURN
SERIES 6
51
Part No Descri
tionItem Qt
Note
26 7013010 1 DECAL, Danger, Cut Finger see decal page
27 7035813 1 SPRING, Torsion
28 7058508 1 SPRING, Extension, 48” HOZ
29 7029425 1 DISCHARGE CHUTE, Hi Impact Co-Polymer
30 7075092 1 V-BELT, HA Sect., 120.722” effective length
31 7043858 8 BUSHING, Flange, .64 x .75 x .5
32 7046301 4 SLEEVE, Caster Wheel
33 7046302 4 WELDMENT, Pivot Yoke, Caster
34 7046720 1 DECAL, Chute/Deflector see decal page
35 7047093 1 COVER, Belt, LH
36 7047094 1 COVER, Belt, RH
37 7090667 2 WASHER, 1/2” Flat
38 7058524 3 ASSEMBLY, 48” Spindle
39 7072319 1 PULLEY, 3-1/4 Dia. Flat Idler New Hampshire p/n FH-5220-14
40 -- 1 *ASSEMBLY, 48” Painted Mower Deck see previous two pages
41 7058086 2 LINK, Leveling (3/8-16 thread)
42 7058087 2 SWIVEL, Support (3/8-16 internal thread)
43 7072044 1 HINGE PIN
44 7091810 2 BOLT, 3/8-16 x 1-3/4” Short Neck Carriage, GR 5 Was 91158
45 7076436 8 SPACER, Blade
46 7073142 4 ROLLER, Low Density Polyethylene Was 79226
47 7091503 6 HAIR PIN, 3/32 x 1-1/2”
48 7091084 4 SCREW, 1/4-20 x 3/8” Hex Washer Self Tap Was 90302
49 7091585 3 NUT, 3/8-16 Hex Center Lock Was 90546
50 7090993 4 SCREW, 1/2-20 x 4-1/2” Hex Head Cap, GR 5
51 7090122 5 WASHER, 3/8” SAE Flat replaces 91514, 91296
52 7090266 4 NUT, 1/2-20 Hex Center Lock, GR 5 or B
53 7091628 4 WASHER, .64 x .99 x .05 Flat
54 7014341 2 RING, .392 External Retaining Waldes #5133-50
55 7018574 1 IDLER, 4.12” Outside Diameter, Flat
56 7024431 1 DECAL, 48” Deck see decal page
57 7034422 1 PULLEY, 5” x .375 Flat Idler (Belt Clutch)
58 7044813 3 PULLEY, Driven, 4.50” O.D.
59 7074467 3 NUT, 3/4-16 Hex Jam, GR 8
60 7014407 3 WASHER, Spindle also shown on 48” SPINDLE
ASSEMBLY page
*NOTE: Deck Ass'y 58522 consists of items 2-9, 11, 13, 14, 21, 24, 38, 58 & 60 assembled with appropriate fasteners.
To Next Page
Loading...
