Why my Soehnle 6958 Scales displays 'EEP.E1'?
The 'EEP.E1' error message indicates that CONFIG or CAL parameters are not correctly set. Reset items in CONFIG mode and perform calibration to resolve this.
Why Soehnle 6958 displays 'EEP.E2'?
The 'EEP.E2' error message indicates that the USER parameter is not correctly set. To fix this, reset items in USER mode.
Why is the battery symbol empty or 'Lo.bAt' shown on my Soehnle 6958?
The empty battery symbol or 'Lo.bAt' message indicates that the batteries are discharged. Charge the batteries to resolve this.
Why Soehnle 6958 Scales cannot display weight in required weighing unit?
If the scales cannot display the weight in the required weighing unit, the unit is not set to enable, or d?5oz when the unit is lb:oz. Enable the unit in CONFIG-UNITS.
What does it mean when my Soehnle 6958 displays '0____'?
The '0____' error indicates that the weight reading is below the Power On Zero limit. Install the platform on the scale and perform zero calibration.
Why Soehnle Scales displays 'STB.ER'?
The 'STB.ER' error can occur because USER-HOLD-STB.TIM is too short or USER-HOLD-HLD.RNG is too small. Set USER-HOLD-STB.TIM longer or set USER-HOLD-HLD.RNG bigger to resolve this.
What does 'PCT.ER' mean on my Soehnle 6958 Scales?
The 'PCT.ER' error means that the unit-percentage-weight is too small. Specifically, the weight of 1%, 0.1%, or 0.01% (determined by CONFIG-FUNC-PERCNT) is less than 0.5d. To fix this, use a greater weight for the sample.
What does 'PWT.ER' mean on my Soehnle Scales?
The 'PWT.ER' error indicates that the piece weight is too small (less than 0.5d). This means the weight on the platform is too small to define a valid reference weight. Use a greater weight for the sample to resolve this.
Why Soehnle 6958 displays 'CAP.ER'?
The 'CAP.ER' error indicates that the capacity parameters are not correct. Set PRIM.N/PRIM.d/SECND.n to the correct number, and make sure the capacity does not exceed 6 digits.
What to do if my Soehnle Scales does not turn on?
If your Soehnle Scales does not turn on, check the following: * Ensure the power cord is properly plugged in and connected. * Verify the power outlet is supplying electricity. * Check the power source. * Replace the batteries if they are discharged.
Detailed specifications including ranges, resolutions, and units.
Diagrams and pin assignments for scale terminal and base connectors.
Step-by-step guide for unpacking and connecting scale platforms and terminal.
Explanation of the terminal display segments and the function of each key.
Mapping of ASCII characters to their corresponding LCD/LED segment display.
Overview of the scale's main display layout and indicators.
Defines the meaning of various icons and symbols shown on the scale's interface.
Instructions for basic weighing, zeroing, and taring operations.
Detailed guide for using the scale to count items based on piece weight.
Procedure for weighing items and displaying their percentage relative to a reference.
How to use the scale to calculate Body Mass Index (BMI) for humans or animals.
Methods for freezing the displayed weight for stable or dynamic measurements.
How to sum up multiple weights, pieces, or percentages for totals.
Procedure to slightly adjust the displayed weight without a standard calibration weight.
List and explanation of all error messages, symbols, and codes displayed by the scale.
Common problems, their probable causes, and recommended solutions for the scale.
General| Graduation | 100 g |
|---|---|
| Display | LCD |
| Material | Glass |
| Tare function | Yes |
| Overload indicator | Yes |
| Automatic shut-off | Yes |
| Power Supply | Batteries |
| Units of measurement | kg, lb |
| Dimensions | 30 x 30 x 2 cm |
To Next Page
